Download Article
Download Article
Learning how to drill pilot holes properly is an essential part of working with wood. A pilot hole is a small hole drilled before driving a screw into a piece of wood. The hole helps in multiple ways: it prevents the screw from splitting the wood; it allows for easier installation in dense hardwoods; and, it ensures that the screw will be installed straight, because it will follow the path of the pilot hole. Before attempting a woodworking project of any magnitude, you should learn how to make a pilot hole.
Steps
Download Article
-
Mark the location of your intended hole with a pencil. If it is crucial that the screw is installed in a precise location, you may want to mark the spot with a pencil on the material. Use a ruler to determine your intended location (usually by measuring the distance from the edge of the material's surface), tracing along the ruler with a pencil. At the desired distance along the line you drew, make a small mark with the pencil.
-
Create an indentation using a center punch. A punch is a small, slender tool with a pointed end that allows you to create a small indentation in the work surface. This indentation will help keep your drill bit from slipping when starting the pilot hole. Position the tip of the punch over your pencil mark, and then strike the punch gently with a hammer.Advertisement
-
Determine the appropriate size bit for drilling your pilot hole. As a general rule of thumb, your pilot hole should be slightly smaller than the diameter of your screw. This will remove as much material as possible, which will reduce the likelihood of splitting, but will still leave enough material for the screw's threads to grip into.
- Exact recommendations for pilot hole diameters based on screw sizes can be looked up online. However, a visual check of your drill bit against the screw will suffice for most applications. It is best to err on the smaller side when choosing a bit; a pilot hole can always be made bigger, but not smaller.
-
Drill the pilot hole. After choosing a bit and fitting it into your drill, position the tip of the bit into the indentation you created with the center punch. Holding the bit at the angle you want the screw positioned, drill the hole to a depth equal to the screw's length. Back the bit out carefully.
-
Install the screw. Once the pilot hole is drilled, you can install the screw. Fit your drill with a screwdriver bit and position the screw's tip into the pilot hole. Drive the screw in, being careful to angle it to follow the path of the hole. Repeat this process for each screw used.
Advertisement
Community Q&A
Search
-
QuestionI don't have a drill and I'm hanging a curtain rod. How do I get the screw started?Community AnswerThe tip of a screwdriver should work.
-
QuestionCan I use a 5/32 bit instead of a 7/32 bit for a pilot hole?Community AnswerYou need the pilot hole to be smaller than the screw diameter you will use, otherwise screws will not hold.
-
QuestionHow do I start a hole in my screen door to put in a new closure?JulieCommunity AnswerYou could use a punch or a screw driver. Just start the screw to puncture or dent the metal.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Video
Tips
- Pilot holes are not necessary when installing screws in very soft materials like gypsum board (drywall). These materials pose little risk of splitting or misaligning your screws.Thanks
- Pilot holes are especially necessary when installing screws near the edge of a piece of wood or into a very thin piece of wood. These tasks present the highest risk that the wood will split when screwed into.Thanks
Submit a Tip
All tip submissions are carefully reviewed before being published
Thanks for submitting a tip for review!
Advertisement
Things You'll Need
- Ruler
- Pencil
- Center punch
- Hammer
- Drill
- Drill bits
- Screw
About This Article
Thanks to all authors for creating a page that has been read 331,421 times.
Reader Success Stories
- "Thank you; I needed to screw some letters to a board and had issues with the wood splitting, so I needed to predrill the screw holes first. I was not sure if the predrilled hole should be larger or smaller than the screw. " ..." more
Advertisement
94%
of readers found this article helpful
.
Click a star to add your vote
% of people told us that this article helped them.
"Thank you; I needed to screw some letters to a board and had issues with the wood splitting, so I needed to predrill the screw holes first. I was not sure if the predrilled hole should be larger or smaller than the screw. "
..."
more
