How to Use a Downrigger Setup

Last Updated: September 16, 2022

Down-rigging is a method of trolling that uses a cannonball attached to an electric or hand-powered winch to carry your fishing line. It also lures down to a specific depth that could not be reached normally. Using down-riggers will allow you to place your lures anywhere from five feet below the surface down to 250 feet (76.2 m), and keep them there consistently. Before you start, your cannonball should be hanging over the edge of the boat near the surface of the water.

Steps

Download Article

Around 80 feet (24.4 m) deep is a good place to start. It is a smart idea to fish an area with a fairly flat bottom with no obstructions (such as trees, rocks). ^{[1]
X
Research source}
Switch your reel to “free-spin” (allows to reel to spin freely, releasing line) by releasing the drag clicker. Put your lure into the water and allow it to feed out about twenty feet. Lock the drag clicker to stop your line and put your rod in the holder. ^{[2]
X
Research source}

Advertisement
Clip the line release clip onto the line (there should be a mark on the clip to show where to clip it on) then lower the cannonball into the water. ^{[3]
X
Research source}

Method 1

Method 1 of 2:

For hand-powered setups

Download Article

1
Do the following: ^{[4]
X
Research source}
- Release the brake while firmly gripping the handle on the reel.
- Lower the cannonball to the desired depth by using the depth counter attached to the spool.
- Lock the brake on the spool to keep the cannonball at that depth.

Method 2

Method 2 of 2:

For motorized setups

Download Article

1
Do the following: ^{[5]
X
Research source}
- Flip the switch that lowers the cannonball
- Watch the counter, and stop the cannonball at the desired depth by flicking the switch back.
- Reel up the slack on your line so that there is a bow in your rod.
- When a fish strikes or your wish to bring up your line, take your rod from the holder. Give it a swift jerk upwards to free the line from the release clip.
- With a manual system, you will have to crank the cannonball up with one hand while you fight the fish with the other (unless you are with someone else). With a motorized system, you just flip the switch. You can fight the fish with both hands while you wait for the cannonball to reach the surface.

Community Q&A

Search

Add New Question

Question

How do I attach the cannonball?

Community Answer

See the little line that is attached with the ball? Simply secure the "line release clip" with the marked clip. It will much easier to perform when you do this in real life.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 1 Helpful 3
Question

What's the distance between the pincher and the lure?

Talha

Community Answer

The distance between the downrigger pincher (release clip) and the lure is a critical factor in successful downrigger fishing. This distance, often referred to as the "lead" or "drop-back," can vary depending on factors such as the species of fish you're targeting, the depth at which you're fishing, and the type of lure or bait you're using. As a general guideline, a common starting point for the lead is around 10 to 15 feet. However, you should experiment and adjust based on the specific conditions and the behavior of the fish. Some species might prefer a longer lead, especially if they are more cautious, while others may strike at a shorter distance.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 1 Helpful 1
Question

How do you adjust the clips for lighter strikes?

Talha

Community Answer

It involves fine-tuning the tension of the release clips. Here's a step-by-step guide: Locate the tension adjustment knob on the release clip. This is usually a small screw or knob near the mouth of the clip. Loosen the knob to reduce tension. This allows the clip to release more easily when a fish strikes with a lighter force. Deploy the downrigger with your lure or bait at the desired depth. Pay attention to how the clip releases when a fish strikes. If it releases too easily, you may need to increase the tension slightly.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 0 Helpful 0

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Video

Tips

Do not insert the line all the way into the line release clip. It makes it very difficult to break off.

Thanks
Helpful 12 Not Helpful 9
It is a very good idea to have a depth finder that works to ensure that you don’t lose your cannonballs on the bottom. It is also smart to be somewhat familiar with the topography of the lake you are fishing.

Thanks
Helpful 7 Not Helpful 5
Keep a close eye on your lines when turning. The line on the outside of the turn will speed up and the line on the inside will slow down. This can allow following fish to catch up to the lure and may cause a strike. Also, avoid turning too sharply as this may cause the lines to tangle.

Thanks
Helpful 8 Not Helpful 10

Show More Tips

Submit a Tip

All tip submissions are carefully reviewed before being published

Name

Please provide your name and last initial

Submit

Thanks for submitting a tip for review!

Warnings

Be sure to know the fishing laws in the area you will be fishing because they are very different in some places. In some places, it is against the law to have more poles in the water than people in the boat.

Thanks
Helpful 5 Not Helpful 3
If a fish strikes the lure be sure to bring up all cannonballs. Be ready to put the boat in neutral in case the fish attempts to swim under the boat.

Thanks
Helpful 3 Not Helpful 1
Cannonballs weigh about 10 pounds, and if dropped, they can damage the boat or cause injuries.

Thanks
Helpful 4 Not Helpful 3
With hand-powered rigs, be sure to hold the handle firmly when releasing the brake as the handle may begin to spin wildly.

Thanks
Helpful 3 Not Helpful 4
Do not stand up while performing this task unless there are railings on the boat, especially in rough waters as you may lose your balance.

Thanks
Helpful 0 Not Helpful 0

Things You'll Need

boat
somewhere to fish
fishing rods (Ugly sticks are optimal. The line should be 20 - 35 lb test)
tackle
fishing net (Use a rubber type net to avoid damaging the slimy coat of the fish, and also prevent hooks from hooking into the net)
pliers

You Might Also Like

[1]

[2]

[3]

[4]

[5]

Log in

How to Use a Downrigger Setup

Steps

For hand-powered setups

For motorized setups

Community Q&A

Video

Tips

Warnings

Things You'll Need

You Might Also Like

References

About This Article

Reader Success Stories

Did this article help you?

About This Article

Quizzes

You Might Also Like

Featured Articles

Trending Articles

Featured Articles

Featured Articles

Watch Articles

Trending Articles

Quizzes

Explore Categories