PDF download Download Article
Getting an even, seamless coat while rolling paint
PDF download Download Article

If you’re itching to do a little DIY makeover in your home, a fresh coat of paint is the perfect place to start. Using a paint roller is the best way to coat a wall easily, but roller marks can leave your paint job looking streaky. Fortunately, there are a few things you can do to avoid roller marks for a smooth, clean finish on your walls.

Things You Should Know

  • Use a synthetic, short-napped roller, which tends to leave fewer marks. Use a vacuum to remove any lint from the roller beforehand.
  • Move the roller back and forth in the paint tray to remove excess paint. Your roller shouldn't be dripping, but it also shouldn't be too tacky or dry.
  • Roll the paint onto the wall in a "W" or "N" pattern to hide seams and streaking. Don't press too hard, and make sure the edges of the rollers are wet with paint.
1

Wipe off any lint from the paint roller.

PDF download Download Article
  1. Use a vacuum or a piece of painter’s tape to clean your roller off before you use it. Even if the roller is new, it still might have a little bit of dust or dirt on it, so give it a quick wipedown before you start. [1]
    • If you’re using an old roller, make sure it doesn’t have any dried paint on it that could cause lumps or bumps in your paint job.
  2. Advertisement
2

Don’t use too much paint.

PDF download Download Article
  1. Pour your paint into a paint tray and dip your roller into the paint. Roll the roller back onto the grooves of the paint tray to squeeze out any excess before you put it on the wall. [2]
    • On the flip side, too little paint can leave your paint job streaky and thin. Try to strike the balance between too much and too little.
3

Roll in a “W” or “N” pattern.

PDF download Download Article
  1. Move your roller up and down at a diagonal to go across your entire wall. Be sure to follow up with new paint before your last coat dries to prevent streaking. [3]
    • Professional painters can paint up and down in straight lines, but it’s a little bit tougher to do. If you’re a beginner, try a W or N pattern to start.
  2. Advertisement
4

Use moderate pressure on the roller.

PDF download Download Article
  1. Instead, press the roller against the wall with moderate pressure; if the paint starts to streak or create lines, you’re probably pushing too hard. [4]
    • This is a little bit objective, and it might take some practice before you find the right pressure point for your paint job.
5

Maintain a wet edge.

PDF download Download Article
  1. This will help ensure that your edges don’t look so defined. It doesn’t have to be a huge overlap—about 1 in (2.5 cm) will do just fine. [5]
    • This is the easiest and best way to make sure you don’t get any streaks in your dried paint.
  2. Advertisement
6

Paint as close to the floor and ceiling as possible.

PDF download Download Article
  1. Try to drag your roller as close to the ceiling and floor as you possibly can without spreading paint everywhere. It will help blend the lines in between your 2 paint jobs and make your walls look seamless. [6]
    • You can paint around the floor and ceiling first to make your paint job easier, or you can save it until the end.
7

Use a synthetic, short-napped roller cover.

PDF download Download Article
  1. When you’re picking out your supplies, go for a 1 4  in (0.64 cm) synthetic, short-napped roller cover for your walls and ceiling. This roller cover doesn’t have any obvious seams, so it will apply your paint smoothly on every surface. [7]
    • Longer-nap roller covers are better for textured walls.
  2. Advertisement
8

Paint the entire wall all at once.

PDF download Download Article
  1. Once you’ve started on a wall, it’s important to go over the entire thing to avoid roller marks. Stopping and starting in the middle of a paint job can lead to uneven drying which creates streaking. [8]
    • Doing an entire wall at once ensures that you’ll keep a wet edge the whole time.
9

Go back over the roller marks while the paint is wet.

PDF download Download Article
  1. Put more paint on your roller and press against the wall lightly on top of the roller marks. Go straight up and down the wall from floor to ceiling to fix the roller marks and spread the paint out. [9]
    • This is also called “back rolling,” and it’s a super important part of smoothing out your paint lines.
  2. Advertisement
10

Sand your walls if you find roller marks.

PDF download Download Article
  1. If your paint dries and you find streaks or marks in your paint, grab a sheet of 180 or 220-grit sandpaper and use it to sand the paint streaks off the wall. [10] Wipe the walls down to get rid of the dust, then cover the entire wall in a new coat of primer and paint. [11]
    • You can also sand in between coats to erase streak marks as they happen.
    • Sanding also works well on paint drips or bubbles.

Expert Q&A

Ask a Question
      Advertisement

      Tips

      • To avoid using a roller all together, try spraying your walls with a spray gun instead.
      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Name
      Please provide your name and last initial
      Thanks for submitting a tip for review!
      Advertisement

      About This Article

      Thanks to all authors for creating a page that has been read 78,112 times.

      Did this article help you?

      Advertisement