Download Article
Replace your dead key fob’s battery in minutes
Download Article
If you think your Nissan’s key fob might be dead, don’t panic! You can easily change out the battery using just a flathead screwdriver or a coin. In this article, we’ll walk you through all the steps you need to get you back on the road again. Plus, we’ll also tell you how you can start your car without a working key fob, in case you’re ever in a jam.
Things You Should Know
- If you have a key inside your fob, remove it or flip it out. Split the fob along the crack using a screwdriver or coin, take the battery out, and replace it.
- When putting the battery back in, make sure the plus sign is facing down. Reassemble the fob and push the two sides together until they click.
- If your key fob is dead, access the emergency key by flipping the latch on the back of the fob.
Steps
Section 1 of 2:
Replacing Your Battery
-
Pull out the emergency key. If your Nissan vehicle doesn’t need a key to start, there should be a little latch on the back of the fob. Pull on it and remove the emergency key. [1] X Research source
- If your key fob has a flip-out key blade, press the silver button in the upper corner to flip the blade out so you can open the fob more easily.
- If your key is for a 2013-2019 Nissan Sentra, unscrew the back. Use a #0 Philips head screwdriver to remove the screw near the bottom of the key. [2] X Research source
- If your fob is a Nissan proximity key for a Micra, Note, or Qashqai model, pull the tab on the side of the key and slide the bottom casing to the opposite side. Pull off the casing. [3] X Research source
-
Pull apart the two sides of the key fob using a screwdriver. Insert a screwdriver into the small slot at the bottom of the fob and twist until the fob pops open. The battery for the remote is the small silver disk on the side of the fob without buttons on the outside. [4] X Research source
- If the model of your car is older, the notch at the bottom of the fob might be wider, making it harder to use a screwdriver. Use a coin instead to easily push open the two sides of the key fob.
- Make sure your hands are clean and free from oil or grease before touching the inside of the key fob. [5] X Research source
Advertisement -
Use a screwdriver to gently pry the battery out. In one of the openings along the battery holder, insert your screwdriver under the battery and lift it out. Carefully hold the battery by the edges and make sure you don’t touch the inner electrical circuits or terminals of the key fob. [6] X Research source
-
Insert the new battery. Make sure that the old battery is the same width and voltage as your new battery. When putting the battery back in, make sure that the side with the specs etched into the battery and the plus sign (+) are face-down in the key fob. Push the battery against the springs on the inside and push down until it clicks into place. [7] X Research source If you’re not sure what kind of battery to get, there may be an engraving in the plastic behind the old battery indicating what type of battery it takes. Here are common battery specs:
- Nissan Altima (2007-2021): CR2032
- Nissan Rogue (2010-2023): CR2032H
- Nissan Rogue (Flip Key Fob) (2014-2020): CR2032
- Nissan Sentra (2013-2019): CR1620
- Nissan Micra, Qashqai, or Note: CR2032
- Nissan Leaf (2010-2020): CR2025 or CR2032 [8] X Research source
- If you’re still not sure what kind of battery your key fob takes, check your owner’s manual.
-
Reassemble the two halves of the key fob. Gently squeeze them together using two hands until they click. If you have an emergency key, push it back in the slot and reset the latch on the back to its original position. [9] X Research source
- If the key fob doesn’t click together right away, make sure that the battery is inserted correctly. If the two sides still aren’t coming together, wrap a piece of cloth around the casing and use a pair of pliers to gently squeeze the two sides together until they click into place. [10] X Research source
-
Test to make sure the key fob is working properly. Press the lock and unlock buttons a couple of times while near your car to see if it locks and unlocks. You will not have to reprogram your key fob after replacing the battery. If your car doesn’t respond, the battery you put in the fob may be dead. Replace the battery with a new one and try again to see if the fob is working correctly.
- Try removing and reinserting the battery. If your fob is still not working, it may be that the battery isn’t seated correctly. Make sure that the battery is in the correct orientation, face down in the fob. [11] X Research source
- If your key fob still doesn’t work, take your Nissan to a mechanic or your auto dealer. There might be a problem with the key fob’s programming or your car’s electrical system.
Advertisement
How Do You Replace The Battery In a Car Key Fob?
Expert Q&A
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Tips
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Expert Interview
Thanks for reading our article! If you’d like to learn more about locks and keys, check out our in-depth interview with Shawn Fago .
References
- ↑ https://www.youtube.com/watch?v=ioyzSDhFeKA
- ↑ https://www.youtube.com/watch?v=D6QowFLHJeE&list=TLPQMTcwNzIwMjMhtlXzzwMSJw&index=3
- ↑ https://www.youtube.com/watch?v=kSU1tXgKLeQ
- ↑ https://www.youtube.com/watch?v=WlrCrFlKim0
- ↑ https://www.youtube.com/watch?v=mm388XmxOA0
- ↑ https://www.youtube.com/watch?v=mm388XmxOA0
- ↑ https://www.youtube.com/watch?v=ioyzSDhFeKA
- ↑ https://www.youtube.com/watch?v=Tgex4QEhCII
- ↑ https://www.youtube.com/watch?v=1luSMdoVQEo
About This Article
Thanks to all authors for creating a page that has been read 17,431 times.
Advertisement