How to Empty a Toilet Bowl for Cleaning, Repair, or Removal

PDF download Download Article
Drain your toilet easily with our expert-approved DIY guide
PDF download Download Article

You may need to drain a toilet to give the bowl or tank a thorough cleaning, especially if you need to do repairs. Fortunately, you can drain a toilet in only a few minutes. All you need to do is shut off the water and flush the toilet to get it to drain. You can then work on or clean the toilet without worrying about excess water. To help you out, we spoke with professional plumber James Schuelke to get expert guidance on getting water out of your toilet the right way.

How to Drain a Toilet

  1. Turn the knob on your supply line counterclockwise to stop your water supply.
  2. Flush the toilet to empty the water in the tank.
  3. Pour around 3 gallons (11 L) of water into the bowl to force flush it.
  4. Use a sponge, wet vac, or turkey baster to remove any remaining water.
  5. If you’re disassembling the toilet, sponge-dry the inside of the tank.
1

Turn off the water supply to your toilet.

PDF download Download Article
  1. Find the supply line leading away from the tank and into the floor or wall, instructs Schuelke. Look for the valve, which is generally a small knob found on the wall or floor near the toilet. Turn the knob completely counterclockwise to turn off the water supply and allow the toilet to drain.
    • Be careful not to break the valve or the pipe if you’re in a really old house. Hold the base of the valve with one hand and turn it with the other.
    2. Advertisement
2

Flush the toilet to drain the water.

PDF download Download Article
  1. Schuelke says you just press down on the handle the same way you normally would when flushing. Hold down and keep pressing on the flush valve until all the water drains from your toilet tank.
    • If the water starts refilling, double-check that you’ve fully rotated the shutoff valve. Make sure you twist it as far as you can (in a counterclockwise direction) to switch off the water supply.
    • If the toilet knob will not shut off properly, try temporarily shutting off the water supply to your house .
3

Soak up any remaining tank water.

PDF download Download Article
  1. There will be a very thin layer of water at the bottom of the tank. If you do want the tank 100% empty, grab a big sponge or dry towel and blot all of the water up.
    • You can skip this step if you’re replacing the entire toilet (the little bit of water left in the tank will evaporate over time). If you’re disassembling the toilet, though, you’ll save a bit of cleanup time by soaking the water up.
    2. Advertisement
4

Get some towels and a bucket.

PDF download Download Article
  1. This is one of those simple DIY jobs that’s going to involve a little cleanup—no matter how careful you are, the process can be a little messy. Lay down a tarp or some old towels near the base of the toilet. This will soak up any water that spills out during the process.
    • Throw some rubber gloves on, too. Getting toilet water on your hands is a little icky—even if the toilet is relatively clean.
5

Pour water into the bowl to force flush the toilet.

PDF download Download Article
  1. Pour 3 gallons (11 L) of water into the bowl. It may seem counterproductive, but pouring a few gallons of water from the sink or tub will force the water through the drain. Lift the lid of the toilet and slowly pour the water into the bowl, lifting the bucket as you pour. This method will draw the water out of the bowl. [1]
    • If pouring slowly doesn’t do the trick, quickly dump the remaining water in the bucket into the bowl, as sudden action can help the water drain.
    2. Advertisement
6

Remove leftover water with a sponge or wet vac.

PDF download Download Article
  1. Grab a wad of paper towels or a sponge. Press this on the bottom of the bowl to soak up any remaining water. [2]
    • You can also plunge the water down the drain by using a traditional plunger.
    • A turkey baster can also remove all of the water if you’re in a pinch.
    • If you are 100% dedicated to not touching any water, use a garden hose to siphon the water into a bucket. Put your finger on the end of a hose, insert the other end into the bowl, and remove your thumb once the hose is over a bucket to drain it out.
    EXPERT TIP

    James Schuelke

    Professional Plumber
    James Schuelke, along with his twin brother David, is the co-owner of the Twin Home Experts, a licensed plumbing, leak detection, and mold inspection company based in Los Angeles, California. James has over 32 years of home service and business plumbing experience and has expanded the Twin Home Experts to Phoenix, Arizona and the Pacific Northwest.
    James Schuelke
    Professional Plumber

    Try using a wet vac instead. To drain a toilet tank, shut off the angle stop or the valve that comes out of the wall below the toilet tank. Once that's shut off, flush the toilet to get the residual water out of the tank, then take a wet shop vac and extract anything that's left.

Expert Q&A

Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
      Advertisement

      Video

      Tips

      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Name
      Please provide your name and last initial
      Submit
      Thanks for submitting a tip for review!

      Warnings

      • Never attempt to drain a toilet without cutting off the water supply. Your toilet will not drain properly if the water is still turned on, and it can cause water to leak, causing a huge mess in your bathroom. [3]
        Thanks
        Helpful 0 Not Helpful 0
      Advertisement

      You Might Also Like

      How to
      Adjust the Water Level in Toilet Bowl
      How to
      Adjust 3 Kinds of Fill Valves on a Toilet
      How to
      Remove & Install a Toilet Fill Valve: A Step-by-Step Guide
      How to
      Unclog a Toilet with a Snake
      Adjusting a Dual-Flushing Toilet Mechanism Made Easy
      How to
      Replace a Toilet Flapper
      How to
      Remove & Replace a Leaking Toilet Flange
      How to
      Increase Water Pressure in a Toilet
      How to
      Stop Toilet Tank Sweating
      How to
      Change a Broken Toilet Handle
      How to
      Level a Toilet
      How to
      Adjust Toilet Tank Handles
      How to
      Fix a Loose Toilet Paper Holder
      How to
      Measure a Toilet's Rough‐In
      Advertisement

      References

      1. ↑ https://www.staugustine.com/story/lifestyle/food/2011/07/07/heloise-keeping-toilet-bowl-fresh-and-clean/16199808007/
      2. ↑ https://www.apartmenttherapy.com/tineco-wet-dry-vacuum-review-37041500
      3. ↑ https://www.home-repair-central.com/how-to-drain-a-toilet.html

      About This Article

      Article Summary X

      To drain a toilet tank, start by turning the small knob at the base of the toilet clockwise to shut off the water supply to the toilet. Next, carefully take the top off of the toilet tank and set it aside. Then, flush the toilet, which will cause the water in the tank to start to drain. Keep holding down the flush valve until the water drains completely from the tank of your toilet. For tips on draining the toilet bowl once the tank is drained, read on!

      Did this summary help you?
      In other languages
      Thanks to all authors for creating a page that has been read 242,078 times.

      Did this article help you?

      Advertisement