PDF download Download Article
Quickly scrub off stubborn polyurethane with these 7 solutions
PDF download Download Article

Polyurethane is a standard wood finishing and protectant for cabinetry, furniture, and floors, which can be applied by brushing, wiping, or spraying onto wood. Water-based finishes have a milky color, while oil-based polyurethane has an amber color. [1] If you're tackling a DIY project and got polyurethane on your hands, fear not! This guide will teach you how to remove it using common home solvents and more.

Things You Should Know

  • Remove oil-based polyurethane using mineral spirits or paint thinner. Or, try cooking oil mixed with salt or nail polish remover.
  • Remove water-based polyurethane using warm water and dish soap, or by scrubbing the area with a pumice stone.
  • Wash your hands thoroughly when you've removed the polyurethane and then apply hand lotion to moisturize your skin.
Section 1 of 2:

Removing Oil-Based Polyurethane

PDF download Download Article
  1. Only use mineral spirits if you have access to a well-ventilated room without the risk of flames, like a bathroom with an open window. Using an old hand towel or rag, apply enough mineral spirits to soften the oil-based polyurethane from your hands. [2]
  2. You may also use cooking oil, like vegetable oil. Simply dab a rag or paper towel with oil and apply to the polyurethane on your skin. [3]
    • For extra scrubbing power, combine 1 2 cup (120 mL) of olive oil (or another oil for your choice) and 1/3 cup (96 g) of salt and stir. Scoop a generous amount and rub the mixture into your skin for approximately 2 to 3 minutes to remove the stain.
    Advertisement
  3. Pour enough paint thinner to coat your hands onto a rag or paper towel. Wipe down each part of your hand before rinsing with soap and hot water. [4]
  4. Pour a decent amount of alcohol onto a rag or paper towel and rub the stained areas until the polyurethane fades. Apply more alcohol if needed. This method will be harsher on your skin, leaving it dry, so moisturize well when you're done. [5]
  5. If you or someone in your house has nail polish remover with acetone, grab it. Soak a rag, paper towel, or cotton balls in the remover and wipe any polyurethane away. [6]
    • If the polyurethane hasn’t dried onto your skin yet, this is a fast removal method.
    • If it has dried onto your skin, you may need to rub it hard or allow it to soak for a few minutes.
  6. Allow your choice of solvent (mineral spirits, oil, paint thinner) to sit on your skin for a minute. Then, wash your hands with warm water and soap to remove any solvents from your hands. Be sure to rinse thoroughly. [7]
    • If your hands still feel sticky, apply more solvent and repeat the process until your hands are clean.
  7. Apply a generous layer of moisturizing lotion to soothe skin irritation and restore moisture to your hands.
  8. Advertisement
Section 2 of 2:

Removing Water-Based Polyurethane

PDF download Download Article
  1. Use a dish soap like Dawn with surfactants, a chemical that can penetrate and lift grease, oil, and dirt from many surfaces. [8] Refer to the back of your dish soap for the ingredients and look for one of the following:
    • Anionic surfactants include Sodium Laurel Sulfate (SLS), Sodium Laureth Sulfate (SLES), and Linear Alkyl Benzene Sulphonic Acid (LABSA). These are the most common surfactants in dishwashing liquids.
    • Nonionic Surfactants are milder and ideal for people with sensitive skin. These include Fatty Alcohol Polyoxyethylene Ether (AEO-9) and Cocamide DEA.
    • Amphoteric Surfactants include Cocamidopropyl Betaine and Cocamidopropylamine Oxide. [9]
  2. Loosen and remove polyurethane from your hands by gently rubbing it with your nails. If it's really stuck, use a pumice stone or a sponge with a rough surface to scrape the polyurethane from your hands. [10]
    • If polyethylene has dried on your skin, you may need to soak your hands in warm water and soap for a few minutes.
  3. Rinse your hands under warm water for at least 30 seconds. If there’s still a stain, repeat these steps until your hands are clean. [11]
  4. After you’ve dried off your hands, apply a generous layer of moisturizing lotion to prevent skin irritation and keep your hands soft.
    • Hand cream can also be used as a preventative measure to protect your skin from polyurethane.
  5. Advertisement

Expert Q&A

Ask a Question
      Advertisement

      Tips

      • Always clean your hands over a sink or bucket to avoid staining other surfaces, like floors, clothes, or rugs.
      • When using chemicals, read the back of the instructions for any additional safety hazards and apply only in well-ventilated areas, free from potential flames.
      • Always wear protective or disposable gloves when handling polyurethane and similar chemicals.
      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Name
      Please provide your name and last initial
      Thanks for submitting a tip for review!
      Advertisement

      Things You’ll Need

      • Dish soap
      • Rough sponge or pumice stone
      • Vegetable oil or olive oil
      • Mineral spirits or paint thinner
      • Salt (optional)
      • Acetone (optional)
      • Rubbing alcohol or denatured alcohol (optional)
      • Hand towel, rag, or paper towel
      • Moisturizing lotion

      About This Article

      Thanks to all authors for creating a page that has been read 13,972 times.

      Did this article help you?

      Advertisement