Download Article
Download Article
Many of the Hampton Bay ceiling fans use a Quick-Install System and use Aero-Breeze™ Technology which can move up to 25% More Air. Here are the steps of how to install one.
Steps
-
Loosen the two screws in the collar on top of the motor assembly. [1] X Research source
-
Remove the canopy ring from the canopy by turning the ring to the right until it unlocks.Advertisement
-
Remove the mounting plate from the canopy by loosening the four screws on the top of the canopy. Remove the two non-slotted screws and loosen the slotted screws. This will enable you to remove the mounting plate.
-
Route the wires exiting the top of the fan motor through the canopy ring. Make sure the slot openings are on top. Route the wires through the canopy and then through the ball/downrod assembly. [2] X Research source
-
Align the holes at the bottom of the down-rod with the holes in the collar on top of the motor housing.
-
Insert the bolt through the holes in the collar and downrod. Be careful not to jam against the wiring inside the downrod. Insert clevis pin and bend to ensure security.
-
Tighten the two screws on the collar on top of the motor housing.
Advertisement
-
Pass the 120-volt supply wires through the center hole in the ceiling mounting plate. [3] X Research source
-
Install the ceiling mounting plate on the outlet box. Slide the mounting plate over the two screws provided with the outlet box. When using close-to-ceiling mounting, it is important that the mounting plate be level. If necessary, use leveling washers (not included) between the mounting plate and the outlet box. Note that the flat side of the mounting plate is toward the outlet box. [4] X Research source
-
Tighten the two mounting screws securely.
-
Lift the assembly up to the ceiling mounting plate carefully. If you are using close-to-ceiling mounting, hang the fan on the hook provided by utilizing one of the holes at the outer rim of the ceiling canopy. If using standard mounting, seat
-
Make sure the tab on the mounting plate socket is properly seated in the groove in the hanger ball.
Advertisement
-
Disconnect the power. If you feel you do not have enough electrical wiring knowledge or experience, have your fan installed by a licensed electrician. Follow the steps below to connect the fan to your household wiring. Use the wire connecting nuts supplied with your fan. Secure the connectors with electrical tape. Make sure there are no loose strands or connections. [5] X Research source
-
Connect the ground conductor of the 120v supply (this may be a bare wire or a wire with green insulation) to the green ground lead(s) of the fan. When using standard ceiling mounting, there are two green grounding leads: one from the ceiling mounting plate and one from the ball/down-rod assembly. When using Close-to-Ceiling mounting, there is only one green ground lead from the mounting plate since the ball/downrod assembly is not used.
-
Connect the fan motor white wire to the supply white (neutral) wire using a wire nut. [6] X Research source
-
Connect the fan motor black wire to the sup-ply black (hot) wire using a wire nut.
-
Spread the wires apart. The green and white wires are on one side of the outlet box and the black wire is on the other side.
-
Turn the wire connecting nuts upward and push into the outlet box
Advertisement
-
Mount the fan blades to the pre-installed blade brackets by aligning the three key-slot holes in the blade with the three posts on top of the blade bracket. [7] X Research source
-
Hold the blade with both hands close to the blade arm and press the blade down firmly. Ensure the key-slot holes are properly seated on the blade bracket posts.
-
While still holding the blade down with both hands, firmly slide the blade away from the motor housing until the blade engages in the locking mechanism. Make sure the steel locking mechanism at the rear of the blade bracket springs upward and butts against the edge of the blade indicating a secure connection. [8] X Research source
-
Visually insect the top of the blade bracket 4 to ensure that the locking mechanism is securely in place.
-
Repeat for the remaining blades.
Advertisement
-
Know that all blades groups by weight. Because natural woods vary in density, the fan may wobble even though the blades are weight matched. The following procedure should correct most fan wobble. Check after each step.
-
Check that all blades are securely mounted 1. to the blade brackets with the locking mechanisms engaged. [9] X Trustworthy Source Energy Star Program run by the U.S. Environmental Protection Agency and Department of Energy focused on educating consumers about energy efficiency Go to source
-
Make sure the blade brackets are not bent 2. out of position and ensure the blade tips are even. Use the enclosed blade balancing kit if the blade wobble is still noticeable by carefully following the instructions included with the kit. [10] X Trustworthy Source Energy Star Program run by the U.S. Environmental Protection Agency and Department of Energy focused on educating consumers about energy efficiency Go to source
Advertisement
Community Q&A
Search
-
QuestionWhat does the blue wire connect to?Community AnswerBlue is usually for the light kit if you have one. It connects to the red in the outlet box if you have a separate wall switch for the light. If you are only using the pull chain to activate the light, it connects to black.
-
QuestionWhat if the chain to turn on the fan will not pull down, yet the light chain works fine?Community AnswerIt is on a separate switch, this switch may be broken or worn out. Turn off power to this fan at the breaker, remove the switch cover and examine this switch. It's possible the switch is just dry and stuck, a little 3-in-1 oil may help, or some part might need replacing. This switch is located inside the housing where the blade arms come together, the light and fan switches are both under this cover.
-
QuestionHow can I connect two green wires from the fan to the ceiling wire?Community AnswerGreen wire is the safety ground. To connect to your fans junction-box with the paper-jacket wire into the metal box with a screw. If the box is plastic, just connect the two wires, green of fan to paper-jacket of feed wire w/ a wire nut.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Tips
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
References
- ↑ https://www.youtube.com/watch?v=D4rLZlSVfw4
- ↑ https://www.thisoldhouse.com/how-to/how-to-install-ceiling-fan
- ↑ https://www.thisoldhouse.com/how-to/how-to-install-ceiling-fan
- ↑ https://www.youtube.com/watch?v=D4rLZlSVfw4
- ↑ https://www.dummies.com/home-garden/home-improvement/electrical-wiring/how-to-install-a-ceiling-fan/
- ↑ https://www.dummies.com/home-garden/home-improvement/electrical-wiring/how-to-install-a-ceiling-fan/
- ↑ https://www.youtube.com/watch?v=VzjW9-xn0Ms
- ↑ https://www.youtube.com/watch?v=VzjW9-xn0Ms
- ↑ https://www.energystar.gov/products/lighting_fans/ceiling_fans/installation_usage_tips
About This Article
Thanks to all authors for creating a page that has been read 169,779 times.
Advertisement