Download Article
Download Article
Technological advancements have created clocks that are efficient and easy to maintain. The most common clock on the market is a quartz clock. It uses a small quartz crystal and electrical currents to keep the time. These clocks are so easy to maintain that you usually only need to replace the battery when they stop working. If the clock gives you problems in spite of a new battery, you should check to make sure the hands aren’t hitting any other part of the clock. Beyond that, it is faster and cheaper to replace the clock movement (the assembly that keeps time) than to try to repair it.
Steps
-
Open the battery compartment. The battery compartment can be found on the back of the clock. The small black box, known as the movement, will house the battery. Use a screwdriver to press in the clip or unscrew it. [1] X Research source
-
Remove the old battery. Use your fingers to pry up one end of the battery. This should release it from the compartment. Dispose of the battery. [2] X Research sourceAdvertisement
-
Clean the terminals. Remove any loose corrosion from the battery terminals. Use a damp q-tip or cotton ball to clean the terminals. [3] X Research source
-
Dry the terminals. With a clean cloth or paper towel, gently dry off the terminals. It is important that the terminals are not wet when a new battery is inserted. If you do not have a clean, dry cloth, let the terminals air dry. [4] X Research source
-
Insert the new battery. Read the instructions in the clock’s battery terminal to determine what type of battery the clock requires. Be sure to line up the positive and negative ends of the battery with the labels in the battery terminal. [5] X Research source
Advertisement
-
Examine the clock hands with the faceplate intact. Watch the clock tick as the time goes by. Determine if the clock’s hands need any adjustment. The clock’s hands should not touch. You will know that the clock’s hands need adjusted if they catch on each other as they rotate around the clock. [6] X Research source
-
Remove the faceplate. Gently remove the faceplate of the clock to make any adjustments to the hands. The faceplate should pop right off. [7] X Research source
- This step is not necessary if the clock does not have a faceplate.
-
Ensure the clock hands do not touch each other. If the hands of the clock do touch, gently bend them away from each other. Be sure not to bend them too far. Just bend them enough so that they are not touching when passing each other. [8] X Research source
Advertisement
-
Take off the faceplate. If your clock has a faceplate, gently remove it. This can be done by simply popping it off of the rim of the clock. [9] X Research source
- This step is not necessary if your clock does not have a faceplate.
-
Lift up the second hand. Remove the second hand by gently lifting it off. Be careful not to damage or bend the hand when you remove it from the clock’s face. [10] X Research source
-
Take off the minute hand. Next, you will remove the minute hand. You will also want to be careful with this hand to not damage or bend it. [11] X Research source
-
Remove the hour hand. The last hand that you should remove is the hour hand. Again, be careful to not damage the hand when you remove it from the clock’s face. [12] X Research source
-
Pull out the movement. The movement is the square box that is sitting on the back of the clock. Gently pull it away from the clock. Be careful to not damage the face of the clock as you are removing the old movement.
-
Insert the new movement. Insert the new movement where the old movement once sat. Be careful to not damage the face of the clock as you insert the movement into the hole in the face of the clock.
-
Replace the hands. Begin replacing the hands by starting with the hour hand, and then the minute hand, and finally the second hand. Be careful to not bend the hands while you are replacing them on the face of the clock. If the hands touch, gently bend them away from each other.
-
Put the faceplate back on. Once you have assembled all of the pieces of the clock, you should put the faceplate back on. The faceplate should pop right back into the edge of the clock.
Advertisement
Community Q&A
Search
-
QuestionWhat if the minute hand is loose?Community AnswerIf your clock uses screws to keep the hands in place, try taking the back off and screwing them tight.
-
QuestionWhen l put a new battery into my clock, l found that the two clock hands are very loose and they won't go around. Is there anything I can do to fix this?Community AnswerIt sounds like the hands have come off the central spindle. This could be caused by the fact that the motor isn't fixed to the back of the clock properly, so when you grip it to fit the new battery it pulls the hands into the dial and loosens them. If you tighten the motor on the back of the clock, the hands should stay in place and it makes replacement of the battery much easier.
-
QuestionWhy will my clock run when lying flat, but quits when hung on a wall?Community AnswerA gear may be loose on the inside. Take it to a repair shop for help.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Video
Tips
- Try to not bend the hands of the clock when removing them.Thanks
- Be gentle with the pieces of the clock to avoid scratching or damaging the face of the clock.Thanks
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement
Warnings
- Bending the hands of the clock will prevent them from ticking correctly.Thanks
Advertisement
References
- ↑ https://www.youtube.com/watch?v=yQJu74wrpxc
- ↑ https://www.youtube.com/watch?v=yQJu74wrpxc
- ↑ https://www.youtube.com/watch?v=yQJu74wrpxc
- ↑ https://www.youtube.com/watch?v=yQJu74wrpxc
- ↑ https://www.hunker.com/12001909/how-to-repair-a-quartz-wall-clock
- ↑ https://www.hunker.com/12001909/how-to-repair-a-quartz-wall-clock
- ↑ https://www.hunker.com/12001909/how-to-repair-a-quartz-wall-clock
- ↑ https://www.hunker.com/12001909/how-to-repair-a-quartz-wall-clock
- ↑ https://www.thriftyfun.com/How-to-Replace-a-Clock-Movement.html
About This Article
Article Summary
X
To maintain a battery-powered quartz wall clock, make sure to replace the battery and reduce friction when needed. If your clock stops working, open the battery compartment on the back of the clock to remove the old battery. Use a damp q-tip or cotton ball to gently wipe down the terminals, then dry them with a clean cloth or towel. Once everything is dry, insert the new battery to get your clock running again. On the other hand, if you notice that the clock’s hands are catching on each other as they rotate around, then you may need to adjust them. Gently bend the hands away from each other to they aren’t touching, which should reduce any friction. To learn how to replace the movement of your quartz wall clock, keep reading!
Did this summary help you?
Thanks to all authors for creating a page that has been read 353,944 times.
Advertisement
