PDF download Download Article
Make a DIY cantenna with this easy guide
PDF download Download Article

This article explains how to make an inexpensive homemade cantenna. A cantenna is an antenna made from a can that can amplify wifi signals from 5-22db in most cases. The cantenna also makes it possible to increase the distance of many wireless networks. In addition, there are many websites that can help you design and see examples of homemade cantennas.

Making a Cantenna

  1. Drill a hole through the center of a 4 in (10.2 cm) wide can.
  2. Insert the adapter into the hole and secure it to the can.
  3. Attach a pigtail cable to the adapter.
  4. Connect the pigtail cable to your WiFi card.
  5. Tape the cantenna to a tripod and adjust it for the best signal.
  1. Watermark wikiHow to Make a Cantenna
    Ideal diameter is 3.25 to 3.75 inches (8.3 to 9.5 cm). A Progresso Soup Can is a good start. Since these are DIRECTIONAL antennas, a longer can will increase range, but they decrease the angle of sweep. This helps eliminate interference, but requires you to point it more accurately. 6 to 10 inches (15.2 to 25.4 cm) long will improve signal strength (gain). You may be able to solder several cans together to improve performance.
  2. Watermark wikiHow to Make a Cantenna
    If you use a single Progresso Soup Can it's easy; count the total number of ribs and punch the hole at exactly the CENTER RIB. One side is N-female for connecting the cable from your wireless equipment, and the other side has a small brass stub for soldering on wire. These can be found at electronics stores internet suppliers. The wire you solder should be exactly 1.21 inches (3.1 cm) tall (just a hair under 1 1/4 inches) sticking up inside the can. You may find soldering or using a small torch melts the plastic insulator in the connector. If so, remove the brass stem from the melted puddle of plastic, use a small torch to solder the wire into the brass stem, then wrap it the brass stem with 10 - 20 turns of black tape and re-insert it snuggly into the adapter, leaving the 1.21 inches (3.1 cm) of copper wire exposed.
    Advertisement
  3. Watermark wikiHow to Make a Cantenna
    Since tin cans rip easily, a hole saw will make a mess. Use a small drill bit and then SLOWLY widen the hole slowly with a rat-tail file, a brad-point drill bit or hole saw held with pliers or vice grips, slowly working it back and forth. A power drill and a big bit will likely to destroy the can or make a poor hole.
  4. Watermark wikiHow to Make a Cantenna
  5. Watermark wikiHow to Make a Cantenna
    Instead of drilling holes and screwing the adapter to the can, you can get a bit of rubber garden hose about 3/8 long, slip it over the outside end of the adapter and as you tighten the cable, the hose compresses against the can and locks the adapter in place.
  6. Watermark wikiHow to Make a Cantenna
    Attach a pigtail cable to the adapter (a pigtail is a wire that attaches the adapter to the computer's wifi card, note you must have a compatible wifi adapter to make this work). One problem with pigtails is the wires are very thin and they just don't last long. A reliable, long lasting alternative is to go to an electronic store and assemble 2 or 3 BNC or BNC reversed connectors, eliminating wire problems. This makes the antenna easily detachable from the USB wifi card with a simple twist-lock.
  7. Watermark wikiHow to Make a Cantenna
  8. Watermark wikiHow to Make a Cantenna
    Tape cantenna to tripod or create a small, portable stand or clamp with a bit of thick wire that loops around the BNC connectors and can be easily removed and allows you to rotate the cantenna to find signals.
  9. Watermark wikiHow to Make a Cantenna
    This should be much stronger than the whip antenna you had before. To improve the signal even more - much more - cut a 2 foot (0.6 m) wide by 1 foot (0.3 m) high sheet of concrete lathing screen with 1 4 inch (0.6 cm) or smaller holes and curve it slightly to form a parabolic dish, similar to a TV satellite dish. Instead of pointing the can at the signal source, point it at your screen which points at the signal so the back of the can points at the signal. It takes a bit of adjusting to get the curve of the screen and distance to the can exactly right. You can find formulas for calculating the exact focal point or use trial and error since you will see your signal gain double or even triple when you get the curve and distance just right. You can then make a wooden or aluminum frame to hold everything together in the right position. You can also use a real satellite dish and place the cantenna at the end of the arm at the position the TV antennas (the horn) usually go.
  10. Watermark wikiHow to Make a Cantenna
  11. Advertisement

Community Q&A

Search
Add New Question
  • Question
    What can I do with this?
    Community Answer
    You can boost your WiFi signal or increase the area that a certain signal is able to reach.
  • Question
    I have an older Dell Inspiron with a WiFi adapter (FreedomPop-U-250) that plugs into the USB. I presently have a whip antenna that plugs into the U-250. It's about the size of a headphone jack. Any way to make this work with antenna?
    Community Answer
    Look up what type of connector it is. I'm guessing from your description it is an SMA, but don't take my word for it. From there, you can purchase or make a pigtail connector and make it work by using the directions in this article to build a cantenna. Also, be sure you are using a WiFi card for this, I looked up the adapter and it comes up as a 3G/4G adapter. 3G and 4G use different frequencies from WiFi. I trust that you are using a WiFi adapter, because my results weren't clear.
  • Question
    How well does this work?
    Community Answer
    VERY. I can usually pick up wifi signals from my nearest Starbucks which is a few blocks away.
See more answers
Ask a Question
      Advertisement

      Video

      Tips

      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Name
      Please provide your name and last initial
      Thanks for submitting a tip for review!

      Things You'll Need

      • N-Female chassis mount connector
      • Four small nuts and bolts
      • A bit of thick wire
      • A can
      • A pigtail Cable
      • wifi adapter
      • wifi source

      About This Article

      Thanks to all authors for creating a page that has been read 444,105 times.

      Is this article up to date?

      Advertisement