Download Article
Have a blast with your very own cardboard skatepark
Download Article
- Ramp |
- Rail |
- Ground Rail |
- Stairs |
- Bowl |
- Half Pipe |
- Using a Sink |
- Buying Pre-Made Pieces |
- Video |
- Tips
When you've got fingerboards, you'll also need somewhere to do the tricks. You can build your own skatepark with a range of jumps and trick mechanisms to make it as fun as possible. You can use one, two or a combination of many of the following suggested items to complete your personalized fingerboard skatepark.
-
1Cut a piece of cardboard into a rectangle. Cut two squares, making the sides as long as the thin side of the rectangle.
- Size the rectangle to match the fingerboard's proportions.
-
2Tape the squares together on one side. Tape the rectangle's short end on one of the sides of the square, opposite the other square.
-
3Tape the rectangles other end to the far square's furthermost end. Make sure the rectangle curves inward.
-
4Cut another square the same size. Tape two of its sides to the other two squares sides on one end of the rectangle.
-
5Cut the excess cardboard off. Tape the side of the end to the curved rectangle. Repeat these steps on the other side.
Advertisement
-
1Cut three squares. Cut one square in half diagonally. Tape the two remaining squares together.Tape the triangles onto the squares so you have a standing triangle thing.
-
2Cut a long strip of cardboard the width of the squares. Tape it to the square on the bottom. Fold it up so that it rests on the triangle. Then tape the two sides to the end triangle.
-
3Cut the excess off and tape the final side.
-
4Make three small thin rolls of cardboard an inch (2.5cm) tall. Tape them upright on the long side of the triangle. Place one in the middle, and the others halfway between the middle and the edge.
-
5Make one last roll, between the width of the squares and the length of the rectangle. Then tape it to the posts.
Advertisement
-
1Cut four squares about 6 inches (15.2 cm). Tape two of them together.
-
2On the other two, draw a pattern that looks like stairs. Make each step about 1 inch (2.5 cm) tall. Start about one inch (2.5cm) from any corner. Cut the pattern out, and keep the two bigger pieces.
-
3Tape them as for the triangles of the grind rail.
-
4Cut 12 6-inch (15cm) by one-inch (2.5cm) rectangles. Tape them into the places on the front of the stairs. [2] X Research source
Advertisement
-
1Cut 21 squares and 4 rectangles. Make 4 ramps using the rectangles and 8 squares. Don't bother making sides.
-
2Tape the bottom of each ramp to another square in the middle.
-
3Note that at each empty corner, make a corner by putting three squares on the floor in the arrangement of an L. Tape the edges together, and stand up the two on the ends of the L. Tape them together to make a corner, and tape it to the ramps. Do this for each corner.
-
4Make a triangle, to put in each corner. This is tricky, because the sides have to be curved correctly, but not at a wrong angle. A good idea is to cut a big rectangle, tape one side correctly, then cut off the excess and cut the rest.
Advertisement
-
1Make 2 good, solid ramps.
-
2Put the two bottom edges together (the places where you would start going up the ramp).
-
3Turn both the ramps over so you see the bottom.
-
4Tape the bottom edges together on the bottom.
-
5Turn the ramps over, so you see the top again.
-
6Tape the edges together again, this side on the top. [3] X Research source
Advertisement
-
1Find a sink. Any sort of sink. You can use that sink as a bowl for the fingerboard.
-
2Get some 300-400 page paperback books.
-
3Open the books so they can be used as a mini ramp directly adjacent to each other. Make sure the covers of the books are facing each other. This creates a mini ramp.
-
4Get the handles from some drawers or cupboards. These can be the rails.
- If you can't get drawer or cupboard handles, squish a ruler between two books.
-
5Stack some books on top of each other to create a staircase.
-
6Have fun in your homemade skatepark in a sink!
Advertisement
-
1Visit online stores that sell toys or miniature items or visit an auction/trading site.
-
2Search for something like "Tech Deck Ramps".
-
3Wait until the list of results comes up. Read the titles, and select the items that are what you want.
-
4Read the description. Read carefully to see exactly what it has. If a used item, look at the pictures carefully to see if it has any damage.
- Email the seller to ask whether there is any damage, and to see if all parts are included, etc.
- Good things to look for are bowls, ramps, rails, stairs, etc.
Advertisement
Expert Q&A
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Tips
- Get creative with your park; anything laying around your house can be an obstacle!Thanks
Tips from our Readers
The advice in this section is based on the lived experiences of wikiHow readers like you. If you have a helpful tip you’d like to share on wikiHow, please submit it in the field below.
- If you are on a budget, Dollar Tree fingerboard builds or parks from Tech Deck are generally better, but if you have a larger budget, you can get professional ledges, rails, and more from Black River.
- You could also try to make some fingerboard obstacles using Legos! They are easier to get and use compared to cardboard.
- 3D printing parts is also a cool idea, like rails and ramps, and even your own finger skateboard!
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement
Video
References
About This Article
Thanks to all authors for creating a page that has been read 235,685 times.
Advertisement
