Download Article
Download Article
This wikiHow teaches you how to disassemble the case of an Xbox 360 classic model. The disassembly process for an Xbox 360 classic model is different than the disassembly process for an Xbox 360 Slim or an Xbox 360 E. Keep in mind that disassembling your Xbox 360 console will void your warranty.
Steps
Download Article
-
Assemble the equipment you'll need. You will need the following items to open your Xbox 360: [1] X Research source
- Flathead screwdriver
- T12 Torx screwdriver
-
Disconnect your Xbox 360 from all input and output sources. Your console should be completely free of any wires or attachments, including external storage, HDMI/audio cables, and the charging cable.
- If there is a disk in the console, eject it and place it somewhere safe before disconnecting your console.
Advertisement -
Ground yourself before taking apart your Xbox 360. Static electricity can permanently damage circuitry, so make sure you practice proper grounding techniques like touching a metal surface before working.
-
Pry off the faceplate. Insert your finger into the USB port section, which is to the right of the power button, and pull the faceplate toward you. You can be relatively firm while doing this—the Xbox 360 doesn't have fragile, touch-sensitive electronics behind the faceplate like later models do.
-
Release the end grilles. These are the grey lattices on the left and right ends of the Xbox 360 case. You can pry loose the grilles in one of two ways:
- Poke a large, bent paperclip through each of the holes in the top row of ventilation spaces on the Xbox 360's casing, prying up each time. This will unhook the clips holding the grille.
- Insert a flathead screwdriver into the space where the grille meets the console case, then work the screwdriver around the grille, prying up as you go. This is less time-consuming than the above method, but runs the risk of breaking the clips that hold the grille in place.
- If you have a hard drive on your Xbox 360, first remove it.
-
Remove the end grilles. Simply pull the end grilles away from the Xbox 360's case and set them aside.
-
Unclip the front of the case. There are four clips on the front of your Xbox 360 that hold the top half and the bottom half of the case together; pull the top of a clip toward you while holding the bottom of the clip to release them. These clips are in the following locations:
- One on either side of the disk tray
- One to the right of the power button
- One on the far-right side of the front of the Xbox 360
-
Unclip the back of the case. Turn your Xbox 360 over so that the back is facing you. Place your hand inside the space on the right where the grille used to be and apply upward and downward pressure to the connected halves of the casing while inserting the flathead screwdriver into the small slots on the back.
- In total, there are seven small slots along the back of the console.
-
Remove the bottom of the case. Flip the Xbox 360 so that its top is face-down, then pull the bottom of the case up and away from the Xbox 360. You should now be looking at the metal part of the Xbox 360's case.
-
Take out the screws holding the top of the case in place. Use your Torx screwdriver for this; if you see a screw that won't fit your screwdriver, don't try to unscrew it—it isn't necessary for disassembly. There are six total screws in the metal part of the case that you'll need to remove:
- Two on the right side
- Two on the left side
- One in each of the indented circles in the middle
- Make sure you place the screws in a plastic bag or a similarly safe place.
-
Flip your console over again. The metal side should be face-down, and the front of the console (e.g., the power button side) should be facing you.
-
Remove the eject button. It's on the left side of the console's front. Gently ease your flathead screwdriver under the green ribbon on the left side of the console's front face and pry. The eject button should pop right off.
-
Lift the top of the case off of the Xbox 360. The case should pull right off, and you should now be looking at your Xbox 360's internal components.
Advertisement
Community Q&A
Search
-
QuestionIs their an easier way to open it?AdabuGabenCommunity AnswerThe only safe way is to follow these instructions.
-
QuestionHow do I remove the back?Community AnswerYou can't.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Tips
- If you're opening your Xbox 360 in hopes of fixing the red ring of death, consider taking the console in to a certified repair shop instead.Thanks
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement
Warnings
- Opening your case will void your warranty. Do this at your own risk.Thanks
Advertisement
References
About This Article
Article Summary
X
1. Get 2 screwdrivers (flathead and Torx).
2. Disconnect all cords from the Xbox.
3. Ground yourself.
4. Pry off the faceplate with a finger.
5. Remove the end grilles with a flathead screwdriver.
6. Unclip the case's front with your fingers.
7. Unclip the back case with the flathead screwdriver.
8. Remove the bottom panel.
9. Remove all screws with the Torx screwdriver.
10. Press Eject.
11. Remove the top cover.
Did this summary help you?
Thanks to all authors for creating a page that has been read 387,768 times.
Reader Success Stories
- "I found a non-working Xbox 360 console, so I wanted to salvage parts. I tried, but it's little different than my other devices/appliances. But wikiHow made my day!" ..." more
Advertisement
"I found a non-working Xbox 360 console, so I wanted to salvage parts. I tried, but it's little different than my other devices/appliances. But wikiHow made my day!"
..."
more
"When removing the upper grill, I didn't know about the hidden tab under one of the rubber feet."
"It helped me clean the inside and helped me a lot!"
