Download Article
Download Article
The brake master cylinder is a key component of a vehicle's brake system. If this component fails, then your vehicle's braking ability will be weakened or destroyed. To avoid this safety hazard, it is best to replace the brake master cylinder. The following is a guide on how to replace a brake master cylinder.
Get Car Support Solve Any Problem
Try Asking:
We’re sorry we don’t support the car you are looking for. Please enter its make, model, and year below so that we can add support for it.
Thank you! We’ll review your request and add support for this product as soon as possible. In the meantime, you can ask more questions about the products we currently support.
Steps
Download Article
-
Locate the various components of the vehicle's brake system. [1] X Research source- Use your vehicle's manual to identify these components.
- Locate the brake fluid reservoir, the brake master cylinder, the brake fluid level sensor, and the brake fluid lines.
- The brake fluid reservoir is usually at the top of the brake system and contains brake fluid. It can be identified by the presence of a threaded cap on top of it.
- The brake master cylinder is typically located directly beneath the brake fluid reservoir.
-
Remove the brake fluid from the brake fluid reservoir. [2] X Research source- Remove the cap.
- Use a siphon or turkey baster to remove the brake fluid.
- Dispose of or recycle the brake fluid in accordance with local laws and regulations. Contact your local agency that deals with household hazardous wastes for any needed information. [3] X Research source
Advertisement -
Remove the brake fluid sensor connector. [4] X Research source- This is part of the brake fluid level sensor that you previously identified from your vehicle's manual.
- This can often be removed by pulling it with your hand.
- Follow the instructions in your vehicle's manual.
-
Remove the brake fluid lines.- Loosen the brake fluid lines with a line wrench.
- Twist the line wrench in a counter-clockwise motion on each brake fluid line until all of them have been removed.
- Keep a towel or cloth handy to clean up any brake fluid that leaks as a result of this procedure.
-
Detach the brake master cylinder. [5] X Research source- Use a socket wrench to remove the mounting bolts from the brake master cylinder. These bolts can be located in your vehicle's manual.
- Remove the brake master cylinder by hand.
-
Install the new brake master cylinder. [6] X Research source- Put the new brake master cylinder in place of the old cylinder.
- Connect the mounting bolts with a socket wrench.
- Tighten to prescribed torque or at least as tight as the old ones were.
- Fill the fluid reservoir with fluid allowing some to run out the brake pipe holes.
- Get somebody to gently pump the brakes while holding a container under the holes.
- This "primes" the cylinder and purges excess air.
- Reconnect the brake fluid lines by turning a line wrench clockwise.
- Reconnect the brake fluid sensor according to the instructions in the vehicle's manual.
- Use the type of brake fluid that is listed on the cap or in your vehicle's manual.
- Bleed the new brake master cylinder.
- Optional - remove front wheel from furthest hub. Push brake cylinder back.
- Optional - remove other front wheel. Push brake cylinder back.
- Optional - If you do this watch for reservoir overflow, catch as required.
- Optional - This effects a "reverse bleed" that releases some air close to the master cylinder.
- Optional - pump brake pedal to return cylinders, top up fluid as required.
- These optional steps make the subsequent bleeding much easier because the air is close to the master cylinder.
- Check pedal free play. If there is an adjuster on pedal adjust to take up slack BUT do not allow no free play. Brakes will bind.
- Brakes must be bled after master cylinder replacement.
- Purchase a bleeder kit from an automotive supply store.
- Follow the directions that come with the kit.
Advertisement
Community Q&A
Search
-
QuestionAfter bleeding my brakes, the pedal is not having pressure, what should I do?This answer was written by one of our trained team of researchers who validated it for accuracy and comprehensiveness.wikiHow Staff EditorStaff AnswerTry bleeding the brakes again. This is a sign of air in the system or a bad master cylinder.
-
QuestionWhat do I need to do to a master cylinder before installing it on a car?Community AnswerThe new master comes with two clear rubber hoses and two plastic nipples that screw into the holes where you would put the brake lines. Screw and tighten the nipples. Fill the master cylinder with fluid. Put one rubber hose in each chamber of the master, and then connect them to the nipples. You need to place the master in a vise, in the round part in the back of cylinder between the two holes where it bolts on. Use a Phillips screwdriver and pump it -- it will be really hard to push, but push until you no longer see bubbles in the clear hoses. Make sure the hoses stay in the fluid -- you may need to have someone hold them while you pump.
-
QuestionWhat is wrong with my brakes if the brake light is on?Community AnswerIf you put you foot behind the brake pedal and pull up and the light goes off, look up in the pedal and see if the electrical switch is loose or broken. If not, you need to have your breaks checked by a mechanic. Make sure it's not your ABS light.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Video
Reader Videos
Submit a Video Tip!
Share a quick video tip and help bring articles to life with your friendly advice. Your insights could make a real difference and help millions of people!
Submit a Video
Coming Soon!
Tips
- If you are uncertain as to whether or not the brake master cylinder must be replaced, check it for fluid leaks. A fluid leak indicates that it must be replaced immediately.Thanks
- Brake bleeding is a two person process. Don't even bother until you have a friend.Thanks
- Bleed the front wheels first. See how it goes - you may not have to bleed all four wheels.Thanks
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement
Warnings
- Do not attempt this if you are a novice or "first timer". Even a small mistake can prove deadly to yourself and others. This is one of the most vital parts of the car. If you are not 100% confident, take it to a shop!Thanks
- Test the brakes before driving in traffic. Press and hold the pedal down. It should stay solid. Confirm that the brakes can hold the car - easy with an auto - put the car in drive and with the brake on apply a bit of gas. Car should not move. At your first opportunity, while driving at around 30 km/h (19 mph), check the rear view mirror, if clear, then apply the brakes quite firmly.Thanks
- If you opt to take the vehicle to an auto mechanic instead of fixing it yourself, exercise caution by driving slowly and allowing plenty of room between your vehicle and other vehicles. Have the vehicle towed if the vehicle's braking ability has been severely reduced or if it no longer works at all.Thanks
Advertisement
References
- ↑ https://www.youtube.com/watch?v=Uz4OwuUGVOA
- ↑ https://www.howacarworks.com/brakes/replacing-a-master-cylinder-and-servo-unit
- ↑ https://earth911.com/recycling-guide/how-to-recycle-automotive-fluids/
- ↑ https://www.2carpros.com/articles/how-to-replace-a-brake-master-cylinder
- ↑ https://www.youtube.com/watch?v=StkzzZWr3Ac
- ↑ https://www.youtube.com/watch?v=fXSmtQu771k
About This Article
Thanks to all authors for creating a page that has been read 370,425 times.
Reader Success Stories
- "I was unsure how to proceed. The information provided was so clear, it gave me the confidence I needed to do the job with confidence." ..." more
Advertisement
"I was unsure how to proceed. The information provided was so clear, it gave me the confidence I needed to do the job with confidence."
..."
more
"Learning how to change a master cylinder was helpful, thanks."
