Retexturing a wall using joint compound (aka drywall mud) is a project that's within reach of practically any DIY'er. As long as you're prepared to get messy, it's totally doable. Pick up some compound and a few other supplies from the hardware store, if you aren't already equipped. After cleaning your walls and preparing the work site, you're ready to begin. Choose a texture pattern that suits your style and go for it! Most techniques only require a few tools, like a trowel, sponge, and paint roller.

Method 1
Method 1 of 2:

Setting Up Your Work Area

PDF download Download Article
  1. Retexturing walls is a job that most DIYers can handle, but if you don't already have all the supplies you'll need, head to the hardware store. Make sure to get:
    • Joint compound (also called taping compound or drywall mud). How much you'll need depends on how much wall area you need to cover.
    • Painter's tape
    • Plastic drop cloths
    • An electric drill and mixing attachment
    • A trowel
    • A putty knife
    • A texture brush or squeegee (optional)
    • A paint roller (optional)
  2. If there is any trim (like crown molding or wainscoting) on the wall you're working with, cover its edges with painter's tape to keep the texturing materials from getting on it. If you do not plan to texture your ceilings, you should also cover the edges where the ceiling meets the wall. Cover the floor of the room in plastic drop cloths to make clean up easier. [1]
    • If there is any furniture in the room you are working in, remove it.
    Advertisement
  3. Drywall mud won't adhere properly if your walls are dirty. Take a clean towel, warm water and a gentle all-purpose clear, and wipe the walls down. Let them dry thoroughly before continuing. [2]
  4. If you are applying drywall mud to an existing gloss or semi-gloss finish wall, it will adhere to the wall much better if you use a primer first. This will give the drywall mud something better to stick to. Apply a layer of primer, such as Kilz, before continuing.
  5. If there are any puncture marks, holes, dips, or other problem spots on your wall, smooth them out before retexturing. Dip a putty knife in joint compound, and smooth the compound directly onto the problem spot to fill it in. Scrape the putty knife over the putty at a 45 degree angle to smooth it out. [3]
  6. Take a 5 gallon (18.9 L) bucket of premixed drywall mud and add 1 inch (2.5 cm) of water on top. Use your drill and mixing attachment to stir until the mix is the consistency of batter. [4]
    • Hold the bucket down while mixing to keep the compound from sloshing over the sides.
    • Keep in mind that you can also mix the drywall powder with water yourself. This also allows you to get it to the desired consistency.
  7. Advertisement
Method 2
Method 2 of 2:

Selecting a Texture Pattern

PDF download Download Article
  1. If you want a thicker texture on your walls, you can work right over whatever is currently on them. Dip your trowel into the compound you mixed, and drag it onto the wall. When the trowel is clear, load it again. Place it near the edge of the first stroke, and drag the second trowel load in a different direction. [5]
    • Keep doing this until the entire wall is covered.
  2. If your current wall texture is relatively smooth and you'd like to keep it that way while still introducing some variation, the stucco look may be for you. Load up your trowel with compound and cover a small area. Press a sponge against the area repeatedly, leaving behind a lightly textured surface. [6]
    • Keep working in small patches until the whole wall is covered.
  3. Take your compound and thin it out even further with water to make a runnier mixture. Use a paint roller to apply the compound all over the wall. The thinner compound will level out existing texture without adding much on top. To complete the smooth finish: [7]
    • Scrape over the compound on the wall with a trowel or putty knife at a 45 degree angle.
    • After the compound has dried, sand the wall. Make sure to wear a ventilator, since this will produce a lot of dust.
  4. This method is popular because it is fast and leaves a pleasantly randomized texture. Dip a paint roller into the drywall mud, then apply it to the wall. Let it partially dry, then go back over the highest “peaks” of the texture and gently smooth them down with a putty knife. [8]
  5. Use a texture brush (a round brush with a handle available in most hardware stores) or cut notches at regular intervals into the rubber portion of a standard squeegee. Apply drywall mud to the wall with a trowel, then smooth it out. While the mud is still wet, run the brush or squeegee over it to create a pattern of lines. For example, you could: [9]
    • Run the brush or squeegee in parallel rows to create a pattern of even lines.
    • Run the brush or squeegee diagonally one direction, then another, to create a crosshatch pattern.
  6. Texture rollers are available in many patterns, so you're sure to find one that suits your style. Pick one up from a hardware store, coat it with drywall mud, then roll it over your walls. Be sure to match up the pattern and roll in a consistent direction so you get an even result.
  7. Whichever texture pattern you choose, you'll need to let things set about 24 hours before continuing. If your region is very humid, it may take longer for the wall to dry. Aiming a fan at the wall can help speed things up. [10]
    • Once the mud has dried, you can paint it however you like.
  8. Advertisement

Expert Q&A

Search
Add New Question
  • Question
    How do you make a textured foam roller?
    Katherine Tlapa
    Interior Designer
    Katherine Tlapa is an interior designer, currently working as a Design Specialist for Modsy, a design service based in San Francisco. She also runs her own DIY Home Design blog, My Eclectic Grace. She received her BFA in Interior Architecture from Ohio University in 2016.
    Interior Designer
    Expert Answer
    The easiest way to add texture to a wall is to paint it with a roller with textured foam. For a DIY option, however, you can wrap your own roller with string or a rubber band.
Ask a Question
      Advertisement

      Tips

      • Some manufacturers produce textured paints that can also be used on your walls. However, these are less forgiving than drywall mud. You will have to work quickly, and apply at least two coats. [11] You can also apply regular paint over the drywall mud.
      • Don't overdo it on corners and edges. You'll probably need less compound there than you think.
      • If you make a mistake with drywall compound, you can wipe it away with a wet towel or sponge before it dries.
      Show More Tips
      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Name
      Please provide your name and last initial
      Thanks for submitting a tip for review!
      Advertisement

      About This Article

      Thanks to all authors for creating a page that has been read 50,064 times.

      Did this article help you?

      Advertisement