PDF download Download Article PDF download Download Article

Canopy tents are perfect for hosting an outdoor event in the shade. Strong winds, however, can move your tent. Luckily, it’s easy to secure your canopy to the ground with ropes. Whether you stake it in the ground or attach weights to the corners, you can entertain in the shade with little hassle!

Method 1
Method 1 of 3:

Securing the Tent with Anchor Ropes

PDF download Download Article
  1. Use a hammer or mallet to pound stakes into the ground. Leave 3 to 4 in (7.6 to 10.2 cm) of the pins above the ground so you can easily tie the anchor ropes to them.
    • Metal stakes can be purchased at hardware stores or specialty outdoor stores.
    • Use a stake on each side of the tent at the corners for additional support.
    • Only use this if you are tying your tent down in grass or dirt. If you are setting up your canopy tent on a hard surface, like concrete , you’ll have to weigh it down.
  2. Make clove hitch knots with braided rope. Make 2 loops near the end of the rope so that the end of the left loop is on top of the rope and the end of the right loop is below the rope. Place the right loop over the left loop so they line up. Set the loops over the stake and pull each side of the rope to firmly tighten it. [1]
    • A clove hitch allows you to adjust the length of the rope easily without undoing the entire knot.
    • Make knots at each of the stakes so the whole tent is secured.
    Advertisement
  3. Sometimes, the frame will have an anchor to tie the rope to. If not, tie it directly to the horizontal frame at the top of the canopy right next to the support pole. [2]
    • You can use another clove hitch knot or make an overhand knot .
  4. Loop the loose end of the rope around the rope pulled taut, making sure the end of the rope goes through the loop. Pull it tight so the excess is taut against the anchor rope. [3]
    • Keep the excess rope up so no one trips or gets tangled up.
  5. Advertisement
Method 2
Method 2 of 3:

Anchoring Your Canopy with Stakes

PDF download Download Article
  1. Most canopies will include the stakes that should be used. If not, purchase a number of T-shaped metal stakes equal to the number of poles on your tent. [4]
    • Metal stakes can be purchased at hardware or outdoor goods stores.
  2. Place the sharp point of the stake through the hole at the bottom of the tent leg. Use a rubber mallet to pound the stakes completely into the ground. [5]
    • If you have sandy or loose soil, stakes will not hold the canopy secure.
  3. Use weights that are at least 20 pounds (9.1 kg) on each leg of your canopy. Though the stakes will hold tightly during small gusts of wind, they may loosen and pull out of the ground during stronger winds. [6]
    • Sandbags can be purchased at hardware stores.
    • Use dumbbells or other weights from home to save money.
  4. Grab the top of the stake with your hand and pull it straight up. You may have to wiggle it slightly back and forth to loosen it. Remove the stakes from each leg before you tear the canopy down. [7]
    • Some mallets have a stake hook on the ends of their handles to easily get leverage on the stake.
  5. Advertisement
Method 3
Method 3 of 3:

Making Weights with Large Buckets

PDF download Download Article
  1. Find buckets that have handles so you can easily carry them and so you have a place to the the ropes. Keep the buckets empty until you get to the location of your tent.
    • Large buckets can be purchased from hardware stores.
    • If you want added support for your tent, purchase 4 more buckets and use 2 at each corner.
  2. Aim to have 40 pounds (18 kg) of material in each of your buckets. [8] This will firmly hold the tent in place without any worry of it moving. If you’re using sand, you only have to fill it two-thirds of the way full to reach the required weight. If you use water, fill the bucket to the top.
    • Mix concrete in the buckets if you want to make permanent weights, though this will make it heavier and more difficult to transport them. [9]
  3. Use an overhand knot to tie braided ropes to the bucket handles. Wrap the end of the rope around the handle and push the tip of the rope through the loop. Pull the knot tight so it is completely secured. If you want added security, make another overhand knot so it is completely tight.
    • If you don’t have handles on your bucket, wrap the rope around the middle of the bucket twice and tie a knot to secure the rope.
  4. Attach the other end of the rope to the horizontal frame at the top of the tent. Wrap the rope around the corner leg as well as the frame to keep the structure sturdy.
    • Use a clove hitch or overhand knot to tie the rope to the frame.
  5. Lift the buckets and slowly work them away from the tent. Don’t move too fast or else you may move the tent as well. Placing the buckets at diagonals will ensure that the whole tent is supported evenly. [10]
    • Keep the buckets even with the outer edge of the tent if you’re using 2 buckets in each corner.
  6. Advertisement

Expert Q&A

Ask a Question
      Advertisement

      Tips

      • Determine if you want your canopy to be a permanent fixture or if you’ll be using it temporarily. This will help determine which anchoring method to use.
      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Name
      Please provide your name and last initial
      Thanks for submitting a tip for review!
      Advertisement

      Things You’ll Need

      Securing the Tent with Anchor Ropes

      • Metal stakes
      • Hammer or mallet
      • Braided rope

      Anchoring Your Canopy with Stakes

      • Metal stakes
      • Rubber mallet
      • Sandbags or weights

      Making Weights with Large Buckets

      • 4 5 US gal (19 L) buckets
      • Sand or water
      • Braided rope

      About This Article

      Thanks to all authors for creating a page that has been read 70,620 times.

      Did this article help you?

      Advertisement