Download Article
Download Article
Formica is a versatile, plastic laminate that comes in a wide range of colors, textures, and finishes. Using Formica allows a homeowner to customize an area with a laminate that is durable and easy to clean. Learning how to cut Formica correctly can save a lot of wasted time and money as sometimes the laminate will want to crack or flake. A few easy steps before actually cutting the Formica can help make your do-it-yourself job look like a professional installation job. There are 2 ways to cut Formica, either with a jigsaw or a laminate router bit. Follow the steps below to learn more about both methods.
Steps
-
Purchase the size of Formica sheet that fits best for your project. Formica sheets are between 1/16 and 1/32 of an inch (.15 and .08 cm) thick. Sheets can be 3, 4, and 5 feet (.9, 1.22, and 1.52 m) wide and 8, 10, and 12 feet (2.44, 3.05, 3.66 m) long. The smallest sheet available is generally a 3x8 feet (.9x2.44 m); however, some home improvement stores offer scrap bins if your project is small.
-
Measure the area you wish to laminate with a tape measure. [1] X Research sourceAdvertisement
-
Mark the cutting line on the Formica with a pen or pencil. [2] X Research source
-
Place masking tape on the cutting line. Use extra layers of tape at the edge of the Formica where the saw will first start the cut. If the line is not visible through the tape, remeasure and remark on top of the masking tape. [3] X Expert Source Eric Shipe
Home Improvement Specialist Expert Interview. 11 June 2021. -
Lay the Formica on a flat, rigid surface. [4] X Research source
- You can use a scrap piece of plywood or OSB as a table to cut Formica. The surface you use will probably be scored by the saws, so be sure that what you are using is safe to cut on and can get damaged.
- Cement would not be a good surface to cut on.
-
Use a circular saw or laminate shears to cut the Formica into large pieces. Do not try to cut a curve with a circular saw. Cut out the shape's form, and leave the trimming for a finer saw and corners for a saw with a some flexibility.
-
Install the Formica onto the countertop or other location.
-
Use a jigsaw with a fine blade to trim the Formica and make any rounded cuts. [5] X Research source
- You can also use a trim router to finish edges if you’d like. [6]
X
Expert Source
Eric Shipe
Home Improvement Specialist Expert Interview. 11 June 2021.
- You can also use a trim router to finish edges if you’d like. [6]
X
Expert Source
Eric Shipe
-
Use a belt sander with a grit of 100 to smooth the edges. Belt sanders can be heavy to operate, and you may choose to sand the edges by hand or with a small metal file. [7] X Research source
Advertisement
-
Cut the Formica to 1/8 inch (.32 cm) larger than the size needed. [8] X Research source
-
Remove any masking tape used for the larger cuts with the circular saw.
-
Install the Formica onto the location.
-
Trim the Formica to the exact size needed. Use a trim router that features a laminate cutting bit. [9] X Research source
-
Use a flat metal file to clean off any burrs or rough edges that may have occurred while cutting the Formica. [10] X Expert Source Eric Shipe
Home Improvement Specialist Expert Interview. 11 June 2021.- You can use sandpaper if you prefer. [11]
X
Expert Source
Eric Shipe
Home Improvement Specialist Expert Interview. 11 June 2021.
- You can use sandpaper if you prefer. [11]
X
Expert Source
Eric Shipe
Advertisement
Expert Q&A
Search
-
QuestionHow do you finish Formica edges?Eric Shipe is a Kitchen and Bath Designer and the Owner of Bath + Kitchen based in Washington DC. Eric and his team specialize in cabinetry, design, and remodels. They serve homeowners, interior designers, architects, and contractors with a refined process, creative ideas, 4K photo-realistic renderings, and 360 Panoramic views. Bath + Kitchen was featured in Best of Houzz 2017-2020. Eric holds a BA in Economics and Business Administration from Ursinus College.Once you have a rough cut done, finish off the edges with a trim router. Attach the Formica sheet to the surface of your choice. There should be a slight overhang; to trim it, place the bearing against that surface, moving the router along the edge until the Formica fits the surface perfectly. Then, sandpaper the edges to finish.
-
QuestionHow do you cut Formica with a jigsaw?Eric Shipe is a Kitchen and Bath Designer and the Owner of Bath + Kitchen based in Washington DC. Eric and his team specialize in cabinetry, design, and remodels. They serve homeowners, interior designers, architects, and contractors with a refined process, creative ideas, 4K photo-realistic renderings, and 360 Panoramic views. Bath + Kitchen was featured in Best of Houzz 2017-2020. Eric holds a BA in Economics and Business Administration from Ursinus College.Use masking tape to cover the points where you plan to make your cuts. Then, trace over the tape and cut.
-
QuestionHow do you cut Formica without chipping it?Eric Shipe is a Kitchen and Bath Designer and the Owner of Bath + Kitchen based in Washington DC. Eric and his team specialize in cabinetry, design, and remodels. They serve homeowners, interior designers, architects, and contractors with a refined process, creative ideas, 4K photo-realistic renderings, and 360 Panoramic views. Bath + Kitchen was featured in Best of Houzz 2017-2020. Eric holds a BA in Economics and Business Administration from Ursinus College.Check if your saw blade is designed to cut laminate or particle board. If you're using a table or circular saw to cut Formica, use a saw blade designed specifically for cutting laminate or particle board. These blades have sharp teeth, which make for cleaner cuts. Try to leave an overhang of up to 1 in (2.54 cm), which you can trim off while finishing the edges.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Tips
- Use the largest size of laminate possible. This can help you avoid seams that could let water through to the substrate or collect dirt.Thanks
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement
Things You'll Need
- Formica
- Tape measure
- Pencil or pen
- Masking tape
- Circular saw or laminate shears
- Jigsaw
- Belt sander with 100 grit paper
- Sandpaper or flat metal file (optional)
- Router with laminate trimming bit
References
- ↑ https://home.howstuffworks.com/best-type-circular-saw-blade-cutting-countertop.htm
- ↑ https://www.thesawguy.com/how-to-cut-laminate-countertop/
- ↑ Eric Shipe. Home Improvement Specialist. Expert Interview. 11 June 2021.
- ↑ https://www.doityourself.com/stry/how-to-cut-formica-sheets
- ↑ https://www.homeownershub.com/woodworking/cutting-formica-laminate-with-jigsaw-302876-.htm
- ↑ Eric Shipe. Home Improvement Specialist. Expert Interview. 11 June 2021.
- ↑ https://diyhousetips.com/how-to-cut-laminate-countertop/
- ↑ https://www.hunker.com/12001646/how-to-use-a-router-to-trim-countertop-laminate-edges
- ↑ https://www.hunker.com/12001646/how-to-use-a-router-to-trim-countertop-laminate-edges
About This Article
Article Summary
X
To cut formica with a circular saw, start by measuring the area you want to laminate with a tape measure and mark the cutting line on the formica with a pencil. Then, put masking tape on the cutting line, lay the formica on a flat surface, and cut along the lines. Once you install the formica, use a jigsaw to do any trimming or make any round cuts. Finally, use a belt sander with a grit of 100 to smooth the edges. To learn how to use a router to cut formica, keep reading!
Did this summary help you?
Thanks to all authors for creating a page that has been read 441,964 times.
Reader Success Stories
- "I learned that Formica can be covered with Formica and how to do it. It gave me a solution for a veneer formal diner table we have." ..." more
Advertisement
100%
of readers found this article helpful
.
Click a star to add your vote
% of people told us that this article helped them.
"I learned that Formica can be covered with Formica and how to do it. It gave me a solution for a veneer formal diner table we have."
..."
more
"Very useful and simply written. I felt as though the users who posted answers were really interested in the questions!"
..."
more
"Excellent instructions without unnecessary wording. Clear and simple wording."
"The instructions and photos are completely clear and easy to follow. Thanks."
"Putting masking tape on your line before cutting to prevent splitting helps."
