PDF download Download Article PDF download Download Article

Kids and grown ups alike are often fascinated by science and chemistry. One great way to keep an audience entertained in a classroom or at home is to make your own hydrogen. Water and acids both contain hydrogen that you can separate to make pure hydrogen gas. You can remove hydrogen gas from water using electricity. Acids are sometimes even easier to use, as many acids will react with metals such as aluminum and generate hydrogen gas. Just remember to be cautious, hydrogen gas can explode.

Part 1
Part 1 of 3:

Electrolyzing Water

PDF download Download Article
  1. Avoid using plastic or metal for this. You will be running an electric current through the water that could melt plastics. Metal will conduct this current and could shock you if you touch the container. [1]
    • If you are unfamiliar with this experiment, start with one cup of water. Producing too much hydrogen can be dangerous.
    • Children should only do this experiment with a responsible/knowledgeable adult.
    • Add a tablespoon of salt to the water for better results — salt will help conduct the electrical current.
  2. While large-scale hydrogen production requires a lot of energy, this experiment can be done with little input. A 9V battery is sufficient to perform the electrolysis (splitting of the water into hydrogen and oxygen). You can also use multiple batteries in series to strengthen the effect. [2]
    • A portable power supply is good for this experiment, as this experiment should be done outside or under a fume hood.
    • While batteries aren’t generally dangerous, you should still wear rubber gloves to avoid being shocked.
    Advertisement
  3. 3
    Connect a paper clip to each terminal of the battery. This will create an anode (the negative paper clip) and a cathode (the positive paper clip). Just wrap the paper clips around the terminals of the battery until they're secure.
  4. When you submerge the paper clips, electricity will flow from the anode, through the water, and to the cathode. Hydrogen bubbles will form at the anode and the cathode will produce oxygen and chlorine gas. [3]
    • Be cautious not to touch the paper clips together.
  5. Advertisement
Part 2
Part 2 of 3:

Reacting Acids

PDF download Download Article
  1. Tear up pieces of aluminum foil and put them into a beaker or other container. Do not use a container with a lid or cap, as this could result in an explosion. There is no need to measure the amount of aluminum used.
    • You could tear a three inch by three inch square of aluminum foil into pieces about the size of your thumb.
  2. Do this experiment outside or under a fume hood. Hydrogen gas disperses quickly, but is very flammable. A buildup of hydrogen gas that is exposed to the air (or any other source of oxygen) can explode.
    • One example of hydrogen gas exploding is the Hindenburg.
  3. There is no need to precisely measure the amount of hydrochloric acid used. The chlorine in the in the hydrochloric acid will react with the aluminum to form aluminum chloride. This will result in the formation of hydrogen gas.
    • Start with about two ounces of hydrochloric acid and add more if needed.
  4. Advertisement
Part 3
Part 3 of 3:

Collecting the Hydrogen

PDF download Download Article
  1. Place the opening of the collection vessel (bottle or balloon) over the opening of your reaction beaker or container. The hydrogen gas is less dense than air and will move up into your collection vessel. This method is often used to blow up a balloon to demonstrate the upward movement of hydrogen gas. [4]
  2. Hydrogen gas can explode if it comes into contact with oxygen. If you are doing electrolysis, do not try to collect any hydrogen when the paper clips are still emitting gas since the gases will be a mixture of hydrogen and oxygen. [5]
  3. You should not collect or store a high volume of hydrogen gas. It poses a serious safety risk, and is difficult to contain. You should do this experiment only for entertainment or educational purposes. [6]
  4. Advertisement

Community Q&A

Search
Add New Question
  • Question
    How do I make a hydrogen balloon?
    Community Answer
    Use a normal balloon, and collect the hydrogen using the instructions above.
  • Question
    Is there a way to avoid it reacting to oxygen?
    Community Answer
    Try to separate the cathode and the anode as far from each other as your container allows you. You can use something similar to a test tube to collect the hydrogen. The best way to do this and obtain the purest hydrogen is to submerge the tube in your container so it fills with water, hold it upside down above the anode and catch the hydrogen. When your test tube is full of hydrogen (which can take a while) you can carefully remove the tube from the water, still holding it upside-down. Now you can use it as you please.
  • Question
    How can I produce H2 with homemade materials?
    Community Answer
    Hydrogen (H2) can be made with a simple homemade apparatus called a voltmeter by electrolysing water (H2O).
See more answers
Ask a Question
      Advertisement

      Tips

      • You can experiment with more or less reactants. This can be done with almost any acids.
      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Name
      Please provide your name and last initial
      Thanks for submitting a tip for review!
      Advertisement

      Warnings

      Advertisement

      Things You'll Need

      • Electrolyzing Water
        • Glass Container
        • Water
        • 9V Battery
        • Paper Clips
      • Reacting Acids
        • Aluminum Foil
        • Hydrochloric Acid
      • Collecting the Hydrogen
      • Balloon or Bottle

      About This Article

      Article Summary X

      To make hydrogen for a science experiment, set up in a well-ventilated and pour 1 cup of water into a glass container. Next, connect a paper clip to each terminal of a 9 volt battery and submerge the paper clips in the water. Then, tear up pieces of aluminum foil, put them into a separate container, and add a small amount of hydrochloric acid to the container. To collect the hydrogen, place the opening of a balloon over the opening of your container and let the hydrogen fill up the balloon! To learn more about safety precautions while performing this experiment, read on!

      Did this summary help you?
      Thanks to all authors for creating a page that has been read 77,277 times.

      Did this article help you?

      Advertisement