Download Article
Download Article
This wikiHow teaches you how to use an empty beer or soda can to marginally increase your Wi-Fi range at home. Keep in mind that using a can to boost your Wi-Fi is unlikely to fix substantial Wi-Fi range issues, and it may actually limit your Wi-Fi's range in one direction.
Steps
Download Article
-
Understand how this works. In theory, placing a sheet of aluminum behind your router will help focus your Wi-Fi toward your preferred source with increased power, thus increasing the range. This can help you stay connected to the Internet on items like consoles or desktop computers that are just outside of your Wi-Fi's range.- This is unlikely to work if your preferred item is more than a few feet outside of your router's Wi-Fi range.
-
Gather the necessary tools. In order to create your Wi-Fi booster, you will need the following items:- An empty, clean 500ml (16.9 fl oz) beer, soda, or otherwise aluminium can
- A Stanley knife or similar safety knife
- A pair of scissors strong enough to cut through thin metal, or a hacksaw
- A small piece of poster tack or similar adhesive
Advertisement -
Wash out the can. Fill up the can with warm water, let it sit for a few seconds, then dump it out and repeat a few more times. Doing this ensures that your can's inside is as clean as possible.- This is easiest to do when your can is freshly empty rather than several hours (or days) old.
- You may want to leave the can upside-down on a paper towel to allow it to dry before you cut into it.
-
Remove the tab from the top of the can. This is most easily accomplished by pulling up on the tab, rotating it 180 degrees, and prying it up until it snaps off.
-
Cut the bottom off of the can. Using a hacksaw or your Stanley knife, remove entirely the bottom of the can.
- Be sure to cut as close to the bottom of the can as is possible.
-
Create the base of the Wi-Fi booster. Cut almost all the way around what used to be the top of the can, making sure to leave around half an inch of the can attaching the top to the rest of the can. At this point, you can flip over the can; the former top will now serve as the can's base.
-
Make a vertical cut all the way down the can. Using your Stanley knife, cut down the side opposite of the section of the can that's attaching the base to the rest of the can.
- The cut should be positioned so that when you spread out the can's sides, the base of the can is centered.
-
Peel out the sides of the can. Now that the sides of the can aren't attached to each other, you should be able to pry them apart to form a radar dish-shaped item.
- Be careful when doing this—the edges of the can are sharp.
- If you notice any remaining residue inside of the can, scrub it out and then dry off the can before proceeding.
-
Place adhesive on the bottom of the Wi-Fi booster's base. Place a small amount of poster tack on what used to be the top of the can. This will help hold the can in place.
- Double-sided tape is another viable option here.
-
Place the booster behind the router. The booster's "dish" should be facing in the direction toward which you want to boost the signal. Depending on how your router is designed, the way that you place the booster may vary:- If your router has an antenna, you should be able to thread the antenna through the drinking hole in the bottom of the base.
- If your router has no antenna, make sure that the can is behind the router, and that the router's front (e.g., the part with the lights) is facing in the direction toward which you want to boost the signal.
-
Enjoy your boosted Wi-Fi. While the boost to your Wi-Fi will be fairly minimal, you may still notice a change in your Internet speed or consistency where you previously struggled.
Advertisement
Community Q&A
Search
-
QuestionDoes this really work?Community AnswerIt reflects a signal from the reflective side (inside of the can) to the antenna and vice versa, causing the signal from the antenna to go in one side. This almost doubles the signal going to the reflective side, while killing the signal on the other side.
-
QuestionHow does this work?Community AnswerThe can is acting as a parabolic reflector, just like on the old multi-element television antennas.
-
QuestionCan I use a plastic bottle instead of a can?Community AnswerNo, as it is not made of a reflective signal material such as aluminum is.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Tips
- Your Wi-Fi will lose some range in the direction away from which the Wi-Fi booster is facing. You can compensate for this by removing the Wi-Fi booster when not using the item for which you're attempting to boost the Internet.Thanks
- If your router is large enough, you may want to create more than one Wi-Fi booster in order to ensure that you're covering the entire back of the router.Thanks
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement
Warnings
- The edges of the can will be extremely sharp after you cut open the can. Consider wearing gloves or some other protective garb while touching the can to avoid cutting yourself.Thanks
- Non-aluminium cans will not boost your wireless signal, nor will plastics, wood, or other non-metal materials.Thanks
Advertisement
About This Article
Article Summary
X
To make a Wi-Fi booster using only a can, start by cutting the bottom off an aluminum can and removing the tab. Then, cut almost all the way around the top of the can, leaving about 1/2 inch so the top is still connected. Next, make a vertical cut all the way down the can except for the lid, and fold the sides of the can down so it's flat. Finally, place the can behind your Wi-Fi router so the lid is on the bottom. For more tips, like how to boost a particularly large Wi-Fi router, scroll down!
Did this summary help you?
Thanks to all authors for creating a page that has been read 1,511,089 times.
Reader Success Stories
- "I loved the simplicity of the article. No plugs and cables or techno-gadgets to contend with or be baffled by. A tin can plus simple tools are the only things required to achieve such a useful and positive improvement in amplifying a Wi-Fi signal." ..." more
Advertisement
"I loved the simplicity of the article. No plugs and cables or techno-gadgets to contend with or be baffled by. A tin can plus simple tools are the only things required to achieve such a useful and positive improvement in amplifying a Wi-Fi signal."
..."
more
