Download Article
Download Article
Stickers are a cinch to apply, but getting them off can be another story. If the tried-and-true technique of peeling slowly from one corner doesn’t work, you may need to get more creative. Try waving a hair dryer over the sticker or soaking water-safe items in hot water to soften the adhesive. To avoid leaving behind irritating residue, you can rub the area around the sticker with an alcohol or oil-based substance to gradually loosen the sticky mess and help the sticker come away clean.
Steps
-
Pry up the corner of the sticker with a thin utensil. If you’re not worried about scarring the surface, a razor blade or putty knife will give you the best results. Otherwise, get your hands on a softer plastic scraper. Work on the outer edge of the sticker until you have enough loose material to grab. [1] X Research source
- Razor blades and other sharp scrapers are best suited for use on glass, smooth, hard metals, and similar materials that aren’t easily damaged. [2]
X
Research source
[3]
X
Expert Source
Chad Zani
Auto Detailing Expert Expert Interview. 2 October 2019. - If you’re in a bind without a lot of options, a credit card or similar object can also do the trick.
- Razor blades and other sharp scrapers are best suited for use on glass, smooth, hard metals, and similar materials that aren’t easily damaged. [2]
X
Research source
[3]
X
Expert Source
Chad Zani
-
Lift the loose corner of the sticker. Pull the flap up and away from the sticking surface, being careful not to force it too much. Hold it in place with one hand and ready your scraping tool with the other.
- Do your scraping with your dominant hand to maximize your efficiency and precision.
Advertisement -
Run the scraper under the sticker using small movements. Push the flat edge of the scraper against the bottom of the sticker where it meets the sticking surface. This little bit of pressure should be enough to break the hold of the adhesive little by little. [4] X Research source- Getting impatient or scraping too aggressively may cause the sticker to tear, forcing you to start the process over again and possibly leaving behind a layer of difficult residue.
- Avoid digging the scraper too hard into the underlying surface. If you’re not careful, it could leave behind unsightly scratches.
-
Continue pulling and scraping until the sticker comes free. After a few passes with the scraper, readjust your grip on the loose edge so that it’s pulled taut. Then, go to work with the scraper some more. Keep at it until you reach the far end.
- If the adhesive is putting up some resistance, try moistening it with warm water (assuming it’s been applied to a waterproof surface). [5] X Research source
- This method is useful for getting rid of slightly older stickers that are too stubborn to peel off by hand, but can’t or don’t need to be treated with heat, oil, or moisture.
Advertisement
-
Set the hair dryer to a high heat setting. Turn the hair dryer on and give it a few seconds to start warming up. The heat from hair dryer will soften the adhesive of old dried-up stickers that have become cemented in place. [6] X Research source
- There’s a chance that direct heat could damage the sticking surface if it’s made from a material like plastic, vinyl, or leather. In this case, it may be better to go with an alternative method of removal. [7] X Research source
-
Hold the hair dryer over the sticker for 30 seconds. Position the nozzle about 1 ⁄ 2 foot (15 cm) away from the sticker. Wave the hot air back and forth from one end to the other. Continue blasting the sticker for up to a full minute. [8] X Research source
- You may notice the sticker material beginning to curl or wrinkle—this is a sign that it’s working.
-
Peel off the sticker by hand. Turn off the hair dryer and set it aside. Loosen one edge of the sticker with your fingernail, then pull it slowly until it comes away clean. Use a soft scraper tool to dislodge any residue that’s left behind. [9] X Research source
-
Continue heating in 30 second intervals. If the sticker is still putting up a fight, you may need to blast it again to get it. Repeat the heating process 2-3 more times, giving it a test pull after each pass. It should only take a couple minutes at the longest to see an improvement. [10] X Research source
- Peeling or scraping the sticker from underneath may help to get it started if the heat alone isn't having the desired effect.
Advertisement
-
Fill a large container with hot water. Whatever container you choose should be big enough to accommodate the item you’re soaking with a little extra room. Turn on the tap and let it run until it’s warm to the touch, then position the container underneath. Don’t get the water too hot—there’s a chance it could scald you or partially melt the item. [11] X Research source
- Leave a few inches of space at the top of the container. You’ll be adding to the overall volume when you insert the item, which could cause it to overflow if you’re not careful.
- This method shouldn’t be attempted to loosen stickers on belongings that are vulnerable to moisture-related damage, like electronics, paper products, or certain types of wood.
-
Submerge the item with the sticker on it into the water. Lower the item slowly to avoid splashing. Make sure the sticker is facing down so that it stays completely immersed the entire time. The heat from the water will begin working its magic right away. [12] X Research source
- You also have the option of running a stream of hot water over the surface of the item if it’s too big to cram into a separate container.
-
Let the item sit for 3-5 minutes. This is the minimum amount of time needed to soften up the sticker enough to remove it by hand. The longer you leave it, though, the better the results will be. If you’re dealing with multiple stickers, you might need to give the item a few extra minutes to soak. [13] X Research source
- Turn items with lots of stickers every so often so that they all spend an equal amount of time underwater.
- Watch for the sticker to fade or wrinkle as the hot water breaks down the adhesive.
-
Peel or scrape away the sticker. Lift the item out of the bath and shake off the excess water. Set it on a stable surface and pull off the sticker in one piece. If it’s still holding on in spots, use a soft scraper tool to coax the adhesive away from the sticking surface. It shouldn’t take much force to get it to let go. [14] X Research source
- The scrubbing side of a dish sponge is perfectly suited for lifting away soggy sticker residue after a long soak, while the soft side can offer a gentler touch for more delicate items.
Advertisement
-
Find a chemical solution safe enough to use on your belongings. When milder methods won't do, you may need to try a special adhesive remover product like Klean-Strip or Goo Gone. If you'd rather not bother with a shopping trip, search your cabinets and equip yourself with some rubbing alcohol, hand sanitizer, WD-40, or a bottle of clear liquor. Any of these items will be potent enough to leave most surfaces squeaky clean. [15] X Research source
- A strong chemical solution will disintegrate the adhesive little by little until it loses its grippiness.
- Alcohol-based products are especially useful for drying out adhesives that have become fused in place.
-
Spread the solution over the sticker. Absorb a small amount of the product into a clean cloth and wipe down the sticker using a circular motion. If you're using a spray cleaner, cover the sticker with a light mist and allow the liquid to settle. Be sure to hit the surrounding area, as well. [16] X Research source
- Make sure the solution doesn’t drip down into the smaller openings of electronics and mechanical items.
- Spot test the item in an out-of-the-way area so you can see how it will react to the product you're using before you slather it on.
-
Let the solution sit for 5 minutes. As it sits, it will begin to slowly seep under the edges of the sticker and go to work directly on the adhesive. When time’s up, pat the area dry with a paper towel to remove the excess cleaner. [17] X Research source
-
Wipe away the sticker. Drag a damp cloth or sponge over the surface to dislodge what's left of the sticker. It should come away in one big piece. Use the product remaining on your scrubber to buff out faint streaks of adhesive or paper left behind.
- If there are any heavy patches of adhesive residue clinging to the surface, apply a little fresh solution and go over it with a little elbow grease.
- Be sure to wash your hands thoroughly after working with harsh chemical cleaners.
Advertisement
-
Grab a product with a high oil content. Chances are, you’ve got plenty of items sitting around on the shelves of your pantry just waiting to be put to use. A bottle of ordinary cooking oil like olive or canola oil, for example, will bust up even the most difficult stickers. You could even use peanut butter or mayonnaise to achieve the same effect! [18] X Research source
- A tablespoon of baking soda can up the unsticking power of oil-based products. [19] X Research source
- These types of substances tend to work best on smooth, hard surfaces that aren't at risk of becoming darkened or discolored by oils.
-
Smear the oil onto the sticker. Use a clean cloth to soak up a quarter-sized amount of oil and rub it over the entire surface. If the product is especially thick, it may help to pick up a flexible utensil like a rubber spatula or brush that will allow you to spread it around exactly where you need it. [20] X Research source
- Avoid pouring thinner oils directly onto the surface. It can be easy to oversaturate it this way.
-
Leave the oil in place for 10-20 minutes. Little by little, it will coat the bonds between the adhesive and the sticking surface and the sticker will begin to slip. The longer you allow it to take effect, the better the outcome will be. Wipe the excess oil away with a paper towel when time is up. [21] X Research source
- Newer stickers may even come unfastened before you ever touch them.
- If you used a thicker oily substance, such as peanut butter, you may need to use a heavier towel or washcloth to expose the sticker underneath.
-
Pull or scrub the sticker away. Scrape up the outer edge with your fingernail, peeling it back gradually until it’s free. A soft kitchen sponge may come in handy for breaking up the last few bits of adhesive. By this point, it will likely have been reduced to a papery goop, so you shouldn’t have too much trouble. Wipe the area clean with a towel and enjoy your new sticker-free surface! [22] X Research source
- Eliminate any remaining patches of residue by blotting the spot with the corner of a towel soaked in oil.
- A light dusting of cornstarch or baby powder can absorb leftover oil coating the sticker surface. [23] X Research source
Advertisement
Expert Q&A
Search
-
QuestionHow do I remove sticky residue from glass?Chad Zani is an Auto Detailing Expert based in Los Angeles, California. He is the Director of Franchising at Detail Garage, an automotive detailing company with locations around the U.S. and Sweden. He and his team are auto detailing experts that offer detailing and car care services.Use a clean razor blade to scrape off the residue. You can also use something like glass cleaner as a lubricant for the razor, if needed.
-
QuestionHow do I remove an emblem from a car?Chad Zani is an Auto Detailing Expert based in Los Angeles, California. He is the Director of Franchising at Detail Garage, an automotive detailing company with locations around the U.S. and Sweden. He and his team are auto detailing experts that offer detailing and car care services.Fishing line will get the emblem off, and then you'll have to deal with sticky residue. Use a combination of a razor blade and a strong, all-purpose cleaner to push the leftover residue in toward itself. With the razor, you should be able to carefully remove anything else that's left behind.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Reader Videos
Tips
- Avoid slapping stickers on any surface you that think might be a pain to remove them from down the line.Thanks
- As a general rule, it’s always best to start with the least intensive method of removal and work your way up from there.Thanks
- Many of these tricks can be employed together to do away with even the most permanently-placed stickers. For instance, you could soak the sticker in hot water and then hit it with a scraper, or heat it with a hair dryer before peeling it up from the corner.Thanks
Tips from our Readers
The advice in this section is based on the lived experiences of wikiHow readers like you. If you have a helpful tip you’d like to share on wikiHow, please submit it in the field below.
- If you don't have rubbing alcohol, a strong spirit like unflavored vodka can also do the trick. Wet a corner of a paper towel and gently scrub the sticker to lift it from the surface.
- I like to use Goo Gone that's specifically made to clean up sticky residue. Just rub it into the surface, and wipe it up with a clean towel.
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement
Warnings
- Steer clear of abrasive scrapers like sandpaper or steel wool. Rough materials like these may permanently scuff up the surface of the item.Thanks
Advertisement
Things You'll Need
- Plastic scraper tool
- Razor blade or putty knife (for hard surfaces)
- Improvised scraper (credit card, scrap plastic, etc.)
- Hair dryer
- Large container
- Hot water
- Dish sponge (optional)
- Oil or alcohol-based
References
- ↑ https://www.stickeryou.com/blog/post/how-remove-sticker-label-adhesive
- ↑ https://www.cars.com/articles/how-to-remove-a-sticker-from-your-car-1420663070247/
- ↑ Chad Zani. Auto Detailing Expert. Expert Interview. 2 October 2019.
- ↑ https://www.cars.com/articles/how-to-remove-a-sticker-from-your-car-1420663070247/
- ↑ https://www.stickeryou.com/blog/post/how-remove-sticker-label-adhesive
- ↑ https://homesteady.com/how-7015418-remove-sticker-unfinished-wood.html
- ↑ https://www.mnhs.org/preserve/conservation/connectingmn/docs_pdfs/repurposedbook-plasticsandmodernmaterials_000.pdf
- ↑ https://www.onegoodthingbyjillee.com/10-ways-to-remove-stickers
- ↑ https://www.youtube.com/watch?v=HDmDbO2yLmw&feature=youtu.be&t=60
- ↑ https://www.onegoodthingbyjillee.com/10-ways-to-remove-stickers
- ↑ https://www.bhg.com/homekeeping/house-cleaning/tips/how-to-remove-sticker-residue-281474979530492/
- ↑ https://www.bhg.com/homekeeping/house-cleaning/tips/how-to-remove-sticker-residue-281474979530492/
- ↑ https://www.youtube.com/watch?v=HDmDbO2yLmw&feature=youtu.be&t=34
- ↑ https://www.cleanipedia.com/gb/floor-and-surface-cleaning/how-to-remove-sticker-residue
- ↑ https://www.bhg.com/homekeeping/house-cleaning/tips/how-to-remove-sticker-residue-281474979530492/
- ↑ https://www.bobvila.com/articles/how-to-remove-sticker-residue/#.WhC21UqnHIU
- ↑ https://www.youtube.com/watch?v=HDmDbO2yLmw&feature=youtu.be&t=22
- ↑ https://www.onegoodthingbyjillee.com/10-ways-to-remove-stickers
- ↑ https://www.youtube.com/watch?v=HDmDbO2yLmw&feature=youtu.be&t=17
- ↑ https://www.bobvila.com/articles/how-to-remove-sticker-residue/#.WhoDQkqnHIV
- ↑ https://www.bhg.com/homekeeping/house-cleaning/tips/how-to-remove-sticker-residue-281474979530492/
- ↑ https://www.onegoodthingbyjillee.com/10-ways-to-remove-stickers
- ↑ https://www.goodhousekeeping.com/home/cleaning/tips/a20519/new-uses-baby-powder/
About This Article
Article Summary
X
To remove stickers from surfaces like metal or glass, try scraping off the sticker with a credit card, razor blade or putty knife. If the item is water-safe, submerge it in hot water for 3 to 5 minutes, then peel or scrape off the sticker. For heat-safe items, try heating the sticker with a blow dryer on the high setting. After 30 seconds, peel off the sticker by hand and use a scraper tool to remove any residue. Alternatively, put a quarter-size amount of cooking oil on a clean cloth, smear it over the sticker, and let it sit for 10 to 20 minutes before peeling or scrubbing the sticker away. For more advice, including how to make your own sticker removal solution with household chemicals, read on.
Did this summary help you?
Thanks to all authors for creating a page that has been read 75,201 times.
Advertisement
100%
of readers found this article helpful
.
Click a star to add your vote
% of people told us that this article helped them.
