Download Article
Keep your breaker circuits working safely and properly with this user-friendly guide
Download Article
A breaker circuit is an electrical switch that cuts off electrical flow in the event of a possible short circuit or overload. This device is essential in a modern world that runs on electricity. Without a circuit breaker, you could find yourself dealing with household fires on a regular basis. While you can easily call a professional electrician, you can also learn how to wire a breaker circuit yourself with relative ease.
Steps
Download Article
-
Switch off the main power switch. This should be located at the top of the breaker panel.
-
Take the cover of the breaker box off.Advertisement
-
Use an electrical tester by putting the tip of one probe against the ground bus bar and the other against one of the screws of a circuit breaker.
- Connected to this screw should be a red, black, or blue covered wire.
- If you have properly turned off the power, there should be no signs of voltage.
-
Remove the covering from one of the holes that runs across the breaker panel's top side. You may need a small, pointy tool, such as a screwdriver, to get them out.
-
Attach a cable clamp through the hole. The cable clamp will keep the four-conductor cable in place after you run it through the hole.
- Remove the lock-nut from the cable clamp.
- Push the cable clamp through the hole. The side that comes through the bottom should have spiral edges for screwing it in.
- Tighten the lock-nut back around the cable clamp by placing it at the underside of the clamp where you see the spiral edges and screwing it in with Channel-Lock pliers.
-
Run a four-conductor cable from the sub-panel breaker box through this clamp and tighten it. You may need a professional to look at your breaker box and tell you which kind of four-conductor cable you need.
-
Cut the covering of the cable and pull this covering away. Inside the covering, you'll find a copper wire (the ground wire), a white covered wire (the neutral wire), a black wire (the hot wire), and a red wire (another hot wire). In the sub-panel box, the neutral and ground wires will connect the same as they do in the main breaker box, but the red and black wires will connect to the hot bar instead of a circuit breaker.
-
Find the ground bus bar. It is a metal strip with a row of screws running down it. Using a flathead screwdriver, unscrew one of them slightly and push your ground wire through. Screw it back in tightly after you insert it.
-
Find the neutral bus bar. Like the ground bus bar, this will be a metal strip with a row of screws, but the neutral bus bar is typically white.
- Take a neutral wire and cut away about a centimeter of the covering at the end of the wire.
- Use your flathead screwdriver to unscrew one of the screws and then push the wire through.
- Screw it back in after you have inserted the neutral wire.
-
Locate an opening for a new circuit breaker.
- You should find a list of acceptable circuit breakers you can use.
- Make sure that your circuit breaker is of acceptable size and voltage.
-
Locate the black hot wire and attach it to the back of the circuit breaker. It will be clearly indicated where this should go. Depending on the kind of circuit breaker you must use, you may have to attach the red hot wire as well.
-
Locate the two sets of clips on the back side of the circuit breaker. One set will be on the left side, and the other on the right side.
-
With the circuit breaker held correctly (the text on it should indicate which way is right side up), push the set of clips at the right side of its back into the plastic bar in the opening.
-
Check once more to make sure the circuit breaker is switched off.
-
Push the left set of clips at the back of the circuit breaker into place on the plastic bar in the opening.
-
Get in touch with a professional electrician to test out your work on the circuit breaker before turning power back on.
Advertisement
Expert Q&A
Search
-
QuestionWhere can I find my circuit breaker?Jesse Kuhlman is a Master Electrician and the Owner of Kuhlman Electric based in Massachusetts. Jesse specializes in all aspects of home and residential wiring, troubleshooting, generator installation, and WiFi thermostats. Jesse is also the author of four eBooks on home wiring including "Residential Electrical Troubleshooting" which covers basic electrical troubleshooting in residential homes.It totally depends on where you live. In the Northeastern United States, for example, you typically find them in the basement. If you're on the West Coast, you see a lot of circuit breakers on the outside of the house. You just kind of have to poke around a bit sometimes to find them.
-
QuestionIs my circuit breaker AC or DC?Jesse Kuhlman is a Master Electrician and the Owner of Kuhlman Electric based in Massachusetts. Jesse specializes in all aspects of home and residential wiring, troubleshooting, generator installation, and WiFi thermostats. Jesse is also the author of four eBooks on home wiring including "Residential Electrical Troubleshooting" which covers basic electrical troubleshooting in residential homes.It's almost always going to be AC. Very few appliances or wiring setups are going to be DC in a residential home.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Video
Tips
- Find a diagram of a breaker box online before getting started. This will help you ensure you are working with the correct wires and bus bars as you wire a breaker circuit.Thanks
- If at any point you feel unsure of what you're doing, consider getting a professional electrician to do this job for you.Thanks
- You can fit a piece of cardboard into the section of the breaker box you're not using as an extra guard against live wires.Thanks
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement
Warnings
- Always double check to make sure you have turned off the main power switch and the circuit breaker power.Thanks
Advertisement
Things You'll Need
- Circuit breaker
- Channel-Lock pliers
- Four-conductor cable
- Flathead screwdriver
- Utility knife
- Electrical tester
About This Article
Thanks to all authors for creating a page that has been read 231,302 times.
Reader Success Stories
- "The directions were well done. Thanks so much for your information. It was invaluable."
Advertisement
"The directions were well done. Thanks so much for your information. It was invaluable."
