Download Article
Download Article
Many drivers experience difficulty starting their vehicles at some point or another. Sometimes, a major part is to blame, but a lot of times this frustrating event is caused by buildup on the battery terminals. Learning how to clean corroded car battery terminals will avoid unnecessary expenses and worry.
Steps
-
Determine the terminal configuration of your battery. There are two types. [1] X Research source- If the terminals are on the side, you will need a 5/16-inch (8 mm) wrench to loosen both cable nuts.
- If the terminals are on top of the battery, you will need either a 3/8-inch (10 mm) or 1/2-inch (13 mm) wrench.
-
Make sure your car is turned off. This will reduce the likelihood of accidentally grounding the cables.Advertisement -
Loosen the nut on the negative (-) cable clamp. Unfasten the cable from the post. [2] X Research source- Do the same for the positive (+) cable. If you have trouble removing either cable, attempt to twist them while pulling up at the same time.
-
Examine the battery for cracks that may be leaking acid. If any are found, you need to replace the battery. -
Check the battery cables and clamps for tears. If a large rip is found, you may have to replace these parts. -
Mix 1 tablespoon (15 ml) of baking soda with 1 cup (250 ml) of very hot water. Dip an old toothbrush into the mixture and scrub the top of the battery to remove corrosion buildup. [3] X Research source- You can even dip the ends of the battery cables in hot water to dissolve any corrosion on the cable ends themselves.
- The buildup is acidic and can burn your skin. To avoid it, wear gloves and safety glasses.
-
Use the toothbrush to scour the battery clamps and posts. Remember to soak your brush in the baking soda solution as much as needed. -
Rinse the battery and cables with cool clean water. Make sure all the baking soda and corrosion is washed away. Dry the battery and clamps with a clean cloth. -
Lubricate all exposed metal on battery terminals, posts and clamps. Use petroleum jelly or a commercial battery terminal protection spray. [4] X Research source -
Reattach the positive (+) cable clamp to the proper terminal. Tighten the nut with your wrench.- Repeat with the negative (-) clamp. Test if terminals are tight enough by twisting each one by hand.
Advertisement
-
Keep a pair of gloves and correct-size wrench in your trunk or back seat. -
Loosen each terminal slightly with your wrench. Do not entirely remove the cables. -
Pour cola over the battery from the center outward in one direction. Repeat going in the opposite direction. -
Allow it to soak for two minutes, then rinse off with water. Tighten the terminals and try to restart the car.
Advertisement
Expert Q&A
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Video
Tips
- You can purchase a battery cleaner spray. Some include an acid detector in the formula. These tend to be less time-consuming, but you must read the directions on the bottle, because each one is different.Thanks
- You can use a battery terminal brush or sandpaper if the buildup is too heavy for a toothbrush.Thanks
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement
Warnings
- The negative cable should always be removed first and attached last to prevent arcing.Thanks
- Always wear protective gear.Thanks
- Remove all jewelry before starting work. Rings and bracelets can become grounded or get caught on engine parts.Thanks
Advertisement
Things You'll Need
- Goggles or safety glasses
- Latex or nitrile gloves
- Wrench: 5/16-inch (8 mm), 3/8-inch (10 mm) or 1/2-inch (13 mm)
- Toothbrush
- Baking soda
- Water
- Cup or bucket
- Terminal brush (optional)
- Petroleum jelly or battery terminal protection spray
References
- ↑ https://www.carquestprofessionals.com/batteries/batteries.html
- ↑ https://www.popularmechanics.com/cars/how-to/a1454/4213127/
- ↑ https://jalopnik.com/heres-the-deal-with-that-white-and-blue-crap-on-your-ca-1796168791
- ↑ https://www.peruzzinissan.com/blogs/385/vehicle-tips/clean-vehicles-battery-terminals/
- https://shop.advanceautoparts.com/r/car-projects/how-to-clean-battery-terminals
- https://www.autos.com/car-maintenance/cleaning-car-battery-terminals
About This Article
Article Summary
X
Before you clean corroded car battery terminals, be sure your car is turned off so you don’t ground the cables. Then, use a wrench to loosen the nuts on the cable clamps, and unfasten the cables from the posts. Next, mix 1 tablespoon of baking soda with 1 cup of very hot water. Dip an old toothbrush into the mixture, then remove any corrosion by scrubbing the top of your battery and the battery clamps and posts. Finally, rinse the battery and cables with cool water and dry them completely before refastening them. For more from our Master Mechanic reviewer on cleaning corroded car battery terminals, including how you can use a soda in an emergency, read on!
Did this summary help you?
Thanks to all authors for creating a page that has been read 1,072,227 times.
Reader Success Stories
- "I am learning the basics of taking care of my vehicle, as I am learning how to do things for myself. A friend of mine told me I should learn some of the minor things myself just in case I go somewhere and I can't get help right away. It will be handy to know these things." ..." more
Advertisement
100%
of readers found this article helpful
.
Click a star to add your vote
% of people told us that this article helped them.
"I am learning the basics of taking care of my vehicle, as I am learning how to do things for myself. A friend of mine told me I should learn some of the minor things myself just in case I go somewhere and I can't get help right away. It will be handy to know these things."
..."
more
"While getting my oil changed today, the guys at Jiffy Lube noticed corrosion on my battery. They were going to charge me $15 to clean it. Thanks to this article, it took me 3 minutes and some baking soda to do it myself. No thank you, Jiffy Lube."
..."
more
"Your article and comment responses educated me greatly. I had only a vague idea of the process, but you were generously explicative and clear about why the steps are the steps and what connects to what from the battery outward--thank you!"
..."
more
"Good to know details; would have saved me a tow truck visit and much fear stopped on the side of the road. Cleaned one terminal, but didn't know how to clean other one covered by plastic sleeve. Now, I know. Thanks very much!"
..."
more
"I'm changing 6 batteries on a golf cart, 3 had terminal buildup/corrosion. Cleaned posts and cables with iron brush, covered all with petroleum jelly. No problems."
..."
more
