Download Article
Download Article
Trusses are commonly used to provide support for roofs, bridges, and other expansive structures. To put together a simple wooden truss, you'll fasten a number of pre-cut beams into a chosen configuration inside a sturdy triangular frame, which will help distribute the weight of the structure more evenly. Plan your project carefully using precise measurements and reinforce the finished truss with both gusset plates and construction adhesive to make sure it’s built to last.
Steps
-
Measure your structure to determine how big your truss needs to be. Trusses can be built in many different shapes and sizes to accommodate the dimensions of various structures. Before you can begin plotting the exact specifications of your truss, find the overall length and height of the structure being reinforced. [1] X Research source
- A truss for a gable roof on one side of your home, for example, might need to be 15 feet (4.6 m) long and 4–6 feet (1.2–1.8 m) tall.
- The dimensions of your structure will determine the angles formed by the truss’s top and bottom beams, or “chords.” On a relatively shallow roof, for instance, the upper and lower chords may meet at a 30-degree angle on each side. [2] X Research source
- In some cases, building codes may dictate the size requirements of a truss for a certain type of structure. Be sure to consult your local building codes before you begin drawing up plans for your truss.
-
Use a simple king post truss to reinforce small, lightweight structures. A king post truss design features a single vertical joist that runs through the center of the triangular frame. This style is useful for framing structures that don’t require quite as much support as structures that bear more weight. [3] X Research source
- A king post truss may be all you need if you're looking to add some extra stability to a garden shed or gable roof .
Advertisement -
Build a Fink truss to bolster a floor, roof, or deck. In a Fink truss, the internal joists are arranged in a “W” shape, ensuring even weight distribution from one end to the other. Fink trusses were originally invented for the purpose of beefing up bridges, but many contractors now use them to increase the strength of interior structures. [4] X Research source
- When fashioning a Fink truss, the middle of the "W" will be at the center line of the triangle. Similarly, the points formed by the internal joists will connect at the midpoints on either side of the center line.
- Due to the symmetrical simplicity of their design, Fink-style trusses can also make an attractive alternative to plainer styles for ornamental structures like gazebos and covered outdoor shelters.
-
Construct a Howe truss to provide unshakable support from below. Howe trusses closely resemble the King Post and Fink styles, only with additional angled beams arranged around the central joist at regular intervals. They are often built onto the underside of the structure they're intended for. [5] X Research source
- The internal angles in a Howe truss are repeated at regular intervals. Both sides of a standard Howe truss, for example, might consist of joists forming opposing 90 and 60-degree angles.
- Because of their complex configuration, Howe trusses tend to be difficult to plan and assemble, and are most often reserved very large load-bearing structures.
- A Howe-style design will offer maximum reinforcement for multi-level structures, as well as those built from especially heavy materials. [6] X Research source
Advertisement
-
Size the bottom chord 0.25 inches (0.64 cm) longer than the floor. Start by noting the exact length of the structure’s floor. Then, add 0.25 inches (0.64 cm). This will account for possible inconsistencies and ensure that the truss is a proper fit. [7] X Research source
- If possible, use a tape measure to double-check the floor’s length rather than simply relying on the recorded measurements listed in the building plan.
-
Incorporate overhanging top chords to add extra visual flair. On some roof trusses, the 2 top chords extend down over the edges of the bottom chord, creating a built-in overhang. If you think you’d prefer an overhang-style truss, adjust the measurements for your top chords accordingly. Your top chords can protrude beyond the bottom chord anywhere from 1–3 feet (0.30–0.91 m). [8] X Research source
- Overhanging chords are more of a stylistic feature than a practical one, and shouldn’t affect the overall stability of the truss.
-
Cut plywood gusset plates to fasten together lightweight trusses. Gusset plates are used to secure the connections between the individual truss components. Fashion your own set of plywood gusset plates by cutting thick sheets of plywood to fit over each site where one joist meets another. This will include all 3 corners of the frame, as well as the top and bottom of each beam crisscrossing the center of the truss.
- Use a circular saw or skill saw to cut your plywood to the right size and shape. [9] X Research source
- Making your own plywood gusset plates will help you keep the overhead for your project low.
-
Use steel gusset plates to secure trusses for weight-bearing structures. Depending on the scale of your project and the specific building codes in your area, you may have the choice to use galvanized steel gusset plates. While these won't be necessary for most projects, they can come in handy for holding together trusses designed for bridges, cathedral-style roofs, or other especially large structures. [10] X Research source
- You can order steel gusset plates from companies that specialize in construction timber or steel-working supplies.
- Solid steel gusset plates cost quite a bit more than plywood ones, so make sure they fit into the budget you've set for your project.
-
Create a detailed sketch of your truss design. Once you have all of your measurements worked out, commit your plans to a sheet of graphing paper. Draw each of the major lines and angles to scale, being sure to note their exact specifications out to one side. Alternatively, you can use an architectural design software to generate a diagram based on the specific measurements you assign. [11] X Research source
- If you’re drafting up your plans by hand, use a ruler to make sure that your lines are straight and the internal angles of the truss are accurately represented.
- You can find many helpful digital design programs for free or cheap online. [12] X Research source
-
Submit your building plans to your local licensing authority. Most cities have agencies responsible for overseeing building codes and regulations. After completing the design for your wood truss, you’ll need to submit a copy to the licensing department for your region in order to have it approved for construction. [13] X Research source
- If you’re not sure who the licensing authority for your area is, run a quick search for “construction licensing” plus the name of your city, state, or territory.
- The criteria used by your licensing department may differ depending on factors like zoning laws, geographical features, and weather patterns. For example, if you live in an area with heavy snowfall, your city will likely have strict requirements about the bearing strength of your new structure. [14] X Research source
- Building codes may not apply if you’re just constructing a truss for simple structures like a small tool shed.
Advertisement
-
Measure and mark your timber with a pencil. Before you begin sawing your raw materials, lay out your lumber on a flat surface and trace a line where you plan on making each cut. Precise measurements are critical if you want your truss to be sturdy and fit together properly. [15] X Research source
- Refer back to the plans you drew up to keep track of how long each piece of lumber needs to be.
- Use a triangle square to verify the angles at the edges of the top and bottom chords.
- Trusses for common structures like houses, carports , and gazebos are most often constructed using 2 in (5.1 cm) x 4 in (10 cm) wooden boards.
-
Cut your truss pieces to size using a jigsaw . A jigsaw will allow you to make short crosscuts through thick pieces of wood with maximum efficiency. Set your lumber on a shop table or between 2 sawhorses and guide the saw smoothly across the measurement lines you drew earlier to achieve clean, precise cuts. [16] X Research source
- To prevent the pieces from shifting, consider using a table clamp to hold them fast to your work surface.
- Always wear gloves and safety glasses to protect yourself from injury while operating a power saw. [17] X Research source
-
Assemble your truss in the desired shape. After cutting your lumber, gather up the individual pieces and begin fitting them together. Remember, you’ll need 2 top chords, 1 bottom chord, and at least 1 central joist for support. [18] X Research source
- Study your plans closely to make sure you're piecing the internal joists together in the correct configuration for the style you've chosen.
- Keep in mind that the angles formed by the internal joists will remain the same despite differences in the frame's height or width.
- This is a good opportunity to visually confirm that each component has been cut to the correct size. If you encounter any mistakes, you may need to start over with a fresh piece of lumber.
-
Use construction adhesive to hold the truss components together. Apply a generous amount of adhesive to the face of each piece where it will intersect with the next using a putty knife. Then, carefully return the piece to its place in the assembly. Press the 2 connecting pieces together for 30-40 seconds to ensure that the adhesive sticks firmly. [19] X Research source
- For ease of application, look for glues that come in tubes similar to caulk guns. [20] X Research source
- Take your time to make sure everything is where it needs to be. With most adhesives, you’ll have a window of 10-15 minutes before the adhesive begins to set. This will allow you to reposition your components as needed.
-
Attach gusset plates at each connection site to fasten the finished truss. Apply a thin layer of construction adhesive to the backside of a plate. Then, flip it over and press it firmly into place over a joint between two truss beams. Insert construction screws every 2–3 inches (5.1–7.6 cm) through the holes in the face of the plate and use an electric drill drive the screws deep into the wood. Repeat this process at each remaining joint. [21] X Research source
- If you're working with plywood gusset plates, you can drill your screws directly through the plates themselves.
- Give the adhesive 1-2 minutes to bond before installing the screws. That way, the friction of the drill won’t cause the plates to slip out of place.
- Allow the adhesive to set overnight. The following day, your truss will be ready to add on to the structure it’s intended to support.
Advertisement
Community Q&A
Search
-
QuestionHow tall do I need it to be for 28 foot wide carport? I want to use 3/12 pitch.Community AnswerAssuming a gable roof -- 1/2 of 28' = 14'. A pitch of 3/12 means a rise of 3" for every 12" of run so 3 x 14 = 42". WARNING: this is a very low pitched roof. In many places the building codes won't allow it (especially in northern climates).
-
QuestionFor a 12 foot by 12 foot shed with a wall height of 8 feet, how high should the center upright be on the truss?Community AnswerIt will depend on the pitch of the roof and the length of the overhang. Provide more information so it can be answered accurately.
-
QuestionWhere can I get metal truss plates?Community AnswerBest place is to go to your local hardware store/lumber yard.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Video
Tips
-
- There are dozens of different truss designs. Read up on the various types to learn more about their unique features and specifications.
Thanks - It's recommended that you buy 10-15% more lumber than you think you'll need to account for possible waste and give yourself a little leeway.Thanks
Tips from our Readers
The advice in this section is based on the lived experiences of wikiHow readers like you. If you have a helpful tip you’d like to share on wikiHow, please submit it in the field below.
- Don't forget to wear your ear and eye protection.
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement
Warnings
- The point of a truss is to provide support, which means constructing one incorrectly could lead to structural defects or, worse, personal injury. If you're not confident in your ability to design and build a truss on your own, hire a qualified contractor to come in and make sure the job gets done right.Thanks
Advertisement
Things You'll Need
- 2 in (5.1 cm) x 4 in (10 cm) wooden lumber
- Plywood or galvanized steel gusset plates
- Construction adhesive
- Measuring tape
- Triangle square
- Jigsaw
- Work gloves
- Safety goggles
- Pencil
- Graphing paper
- C-clamp (optional)
References
- ↑ https://docs.lib.purdue.edu/cgi/viewcontent.cgi?article=1836&context=agext
- ↑ http://cwc.ca/wp-content/uploads/trusses-ApplicationsHistoryDesignandManufacturing.pdf
- ↑ http://www.tbcbspa.com/trusses.htm
- ↑ http://cwc.ca/wp-content/uploads/trusses-ApplicationsHistoryDesignandManufacturing.pdf
- ↑ https://www.garrettsbridges.com/design/howe-truss/
- ↑ http://www.cascade-mfg-co.com/media/a-builders-guide-to-trusses.pdf
- ↑ https://www.youtube.com/watch?v=evu1TATBX44&feature=youtu.be&t=218
- ↑ http://cwc.ca/wp-content/uploads/trusses-ApplicationsHistoryDesignandManufacturing.pdf
- ↑ https://www.youtube.com/watch?v=fi_MhPNGP80&feature=youtu.be&t=77
- ↑ http://cwc.ca/wp-content/uploads/trusses-ApplicationsHistoryDesignandManufacturing.pdf
- ↑ http://cwc.ca/wp-content/uploads/trusses-ApplicationsHistoryDesignandManufacturing.pdf
- ↑ https://www.researchgate.net/publication/242266354_Practical_Approach_to_Designing_Wood_Roof_Truss_Assemblies
- ↑ http://www.rld.state.nm.us/uploads/FileLinks/49cda9a3a6f04aa9a169e9301ea1ebfc/BLDG_RES_GUIDE_070811.pdf
- ↑ https://codes.iccsafe.org/public/document/IBC2018/chapter-23-wood
- ↑ https://www.youtube.com/watch?v=evu1TATBX44&feature=youtu.be&t=335
- ↑ https://www.familyhandyman.com/tools/woodworking-tools/how-to-use-a-jigsaw/view-all/
- ↑ http://www.technologystudent.com/pwtol/jigsaw1.htm
- ↑ http://cwc.ca/wp-content/uploads/trusses-ApplicationsHistoryDesignandManufacturing.pdf
- ↑ https://www.youtube.com/watch?v=evu1TATBX44&feature=youtu.be&t=1091
- ↑ https://www.naturalhandyman.com/iip/infadh/infadhi.html
- ↑ https://www.youtube.com/watch?v=evu1TATBX44&feature=youtu.be&t=1091
About This Article
Article Summary
X
To build a simple wood truss, start by measuring the length and height of the structure you're reinforcing to determine how big your truss should be. Then, plan for the bottom chord of the truss to be 1/4 inch longer than the floor of the structure. If you're trying to reinforce a shed or gable roof, use a simple king post truss design, which has a single vertical joist running through the center of the triangular frame. For larger structures like floors, roofs, or decks, try a Fink truss design, which has internal joists arranged in a "W" shape for extra support. To learn how to assemble a wood truss, scroll down!
Did this summary help you?
Thanks to all authors for creating a page that has been read 1,078,533 times.
Reader Success Stories
- "I always try to build something myself before the Scottish in me lets me open my wallet, so this article will really help when I go to build my shop. Realistically I will never build anything larger then that without a contractor or engineers approval." ..." more
Advertisement
"I always try to build something myself before the Scottish in me lets me open my wallet, so this article will really help when I go to build my shop. Realistically I will never build anything larger then that without a contractor or engineers approval."
..."
more
"It is helpful to have both pictures and photos. Each shows particular aspects and helps illustrate the points."
"I understanding the basis for a simple truss without over-engineering a simple gazebo roof."
"A very useful guide to the start of my home-built roof."
"The steps are easily explained."
