PDF download Download Article PDF download Download Article

Most computer retailers offers the Linksys WRT54G Wireless Router for about $49 and Wireless Access Points for $99. Why waste $50 if you don't have to? You can convert a wireless router to become a simple access point if that's all you need. This is not an article on how to create a wireless-to-wireless bridge, as some have misinterpreted it to be. It is just to add a simple wireless access point to an existing wired network.

  1. Document your current network's IP address scheme. In this example, the existing router was 192.168.0.1. DHCP settings and subnet mask does not matter for this example. Substitute your network addresses in place of these settings if yours is different.
  2. Do not connect any cable to the "WAN" port.... Ever. Put a new piece of tape over the "WAN" port socket to prevent you from trying.
    Advertisement
  3. Take a new cable and plug into LAN port #2 on the new Linksys router and the other end into the network jack of your PC.
  4. Plug the power supply into the AC mains and the output cable and plug into the power jack on the rear of the router. One or more lights should become illuminated on the front to indicate it has been successfully powered up.
  5. Resetting ensures that any customized settings are erased and the router is returned to factory defaults. This usually isn't required on a new router, but if you suspect the router was returned and resold to you, it may not function as expected without resetting first (this is also the only way to access the setup page if you forget the login username and password). Consult the manual for the location of the reset button, as it varies depending on model - but is usually found on the rear panel near the power jack.
  6. After reboot, start your browser and type in: http://192.168.1.1 - you will be asked for: Login ID = admin , and a Password = admin (Linksys defaults). If 192.168.1.1 will not load, try 192.168.0.1 or 192.168.2.1 instead. The manual will provide the default IP address for the router if the router fails to produce a login page. This can also indicate a router that has not been restored to factory defaults via reset procedure detailed above.
  7. Go to the Wireless Configuration page and start configuring the wireless options, such as Wireless SSID - Do not use "linksys", pick something else, like "charlie". The SSID must match that of the primary router and the channel must be different than that of the primary router (Channel 1 for primary router and 6 or 11 for secondary router are good choices as they are separated enough by frequency).
  8. In the Wireless security settings page, use "WPA-Personal" level security at minimum, and a wireless security key at least 8 digits/letters long and you are done. Use of your cell phone number can be a good security key choice, as these numbers are not listed in any directory, etc. Save the settings.
  9. I set mine to the highest number in my network: 192.168.0.254. This puts the access point "out of the way", so to speak. Note: Some network routers are set by default to "start" in the high range (xxx.xxx.xxx.254), so if your network is like this, set the new wireless device to a lower unused number. 192.168.0.253 will do.
  10. There only needs to be a single DHCP server on most small networks or subnets. The original, main router (either a stand alone type or one built into your provider's cable modem or DSL modem) will provide IP addresses to all devices connected to it - including those that connect thru the access point just created.
  11. Advertisement

Community Q&A

Search
Add New Question
  • Question
    How do I setup a long range WiFi receiver?
    Community Answer
    You can use a Linksys range expander. Bypass your WRT54G and make it a switch, your range expander will then act as your main router.
Ask a Question
      Advertisement

      Tips

      • Do not use the IP addresses in this example unless your network is exactly the same.
      • If you mess up, put everything back like it was, and reset the Linksys Router. Start from step 1 again.
      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Name
      Please provide your name and last initial
      Thanks for submitting a tip for review!
      Advertisement

      Warnings

      • Take note of the Wireless Security settings (Step 6). Do not leave your signal unprotected, it is an invitation for hackers and freeloaders to steal your network bandwidth, or worse.
      Advertisement

      Things You'll Need

      • A Linksys WRT54G Wireless Router
      • A new Ethernet cable
      • A Desktop/Laptop Computer
      • About 15 minutes

      About This Article

      Thanks to all authors for creating a page that has been read 748,577 times.

      Is this article up to date?

      Advertisement