PDF download Download Article PDF download Download Article

Making a mini-electromagnet is a simple project that you can complete just for fun, or to use as an educational experiment. It only takes a few minutes to create a mini-electromagnet, but you will need some special materials to do it. After you have completed your first mini-electromagnet, you can also make modifications to your creation that might make the magnet more powerful.

Part 1
Part 1 of 2:

Making a Mini-Electromagnet

PDF download Download Article
  1. Making a mini-electromagnet is a fun, easy project. You can use it to learn more about how magnets work, or just as a way to pick up some paperclips that you spilled on your desk. To make a mini-electromagnet, you will need: [1]
    • nail or screw (at least three inches long and made from iron, zinc, or steel) [2]
    • some thin, coated copper wire
    • scissors
    • one AA battery
    • electrical tape
    • something to pick up, such as metal paperclips or tacks
  2. Watermark wikiHow to Create a Magnet With a Wire and a Nail
    Take your nail or screw and begin wrapping the copper wire around it, but make sure that you leave a tail of about three inches. You will need this to connect the wire to the battery. [3]
    • Coil the wire tightly around the nail or screw until you reach the end. Then, leave another three-inch tail. Cut the wire about three inches past the end of the nail or screw.
    • When you are done, you should have two three-inch pieces of copper wire hanging off of the ends of your screw or nail.
    Advertisement
  3. Watermark wikiHow to Create a Magnet With a Wire and a Nail
    Take the wire pieces that are hanging off of the ends of your screw or nail. Then, curl up the ends of these pieces of wire a little bit, as if you are making a tiny loop on each end. [4]
    • Looping the ends of the wire will help to create a better connection between the battery and the wire.
  4. Watermark wikiHow to Create a Magnet With a Wire and a Nail
    Next, take the loops that you created and attach one loop to each pole of your battery. Attach one to the positive pole and the other to the negative pole. [5]
    • Secure each of the wire loops to the opposite poles of your battery with a small piece of electrical tape.
  5. Watermark wikiHow to Create a Magnet With a Wire and a Nail
    After you have attached the wires and secured them with tape, your mini-electromagnet is complete. Now you can use the wire-wrapped part of the nail or screw to pick up things like paperclips, tacks, nails, screws, and other small metal objects. [6]
    • If your mini-electromagnet does not work, then check to ensure that the wires are making close contact with both ends of the battery. If they are loose or not connected, then the electromagnet will not work.
    • Detach the copper wires from the battery when you are done using the magnet. The magnet will become hot if the wires are connected for too long.
  6. Advertisement
Part 2
Part 2 of 2:

Modifying the Design

PDF download Download Article
  1. You might find that different materials have different levels of magnetism. Try swapping an iron nail for a steel one to see if this increases or decreases the amount of paperclips you can pick up.
    • Don’t forget to count the number of paperclips that your current design can lift before you make adjustments.
  2. [7] A larger screw or nail may also have more magnetic power than a small one because you can coil more copper wire around it. Try upgrading your current screw or nail with a larger one to see if this makes the magnet more powerful.
  3. [8] AA batteries work well for this experiment, but maybe a larger battery will make your electromagnet more powerful. Try swapping your AA battery for a D battery to see if this results in a more powerful magnet.
    • Attach the wires to the D battery the same way that you would attach them to the AA battery.
  4. Watermark wikiHow to Create a Magnet With a Wire and a Nail
    By adding a knife switch, you can control the flow of power with the push of a button. To add a knife switch, you will need two D batteries, more wire, and a knife switch, which you can find in most hobby stores.
    • Coil the wire around your nail or screw, then connect the wire from one end of the screw to your knife switch.
    • Then, connect the wire from the other end of the nail or screw to the negative pole of one of the D batteries.
    • Next, connect a piece of copper wire between the positive pole of your battery that is connected to the screw and the negative pole of the battery that is not yet connected to anything.
    • Finish the circuit by connecting a wire between the remaining positive pole and the knife switch.
    • Close the knife switch and you should be able to pick up some paperclips or tacks.
  5. Advertisement

Video

Community Q&A

Search
Add New Question
  • Question
    Why is it that the nail becomes hot when I connect to the charge?
    Shawn Berlinghoff
    Community Answer
    The nail becomes hot because the wire is becoming hot. The wire becomes hot whenever it is too small for the amount of electricity you're trying to push through it. To stop this problem simply increase the gauge of wire.
  • Question
    Does the battery still need to have a charge?
    Community Answer
    Yes. A battery that does not have a charge will probably not work, or at least not as well as one that has a full charge. Try to do the experiment with a new battery for best results.
  • Question
    When do electromagnets acquire magnetism?
    Harigovind R
    Community Answer
    Electromagnets acquire magnetism when electrons flow through them. That's why electromagnets work only when there is a potential difference at its ends. For making that potential difference, we connect a battery to it.
See more answers
Ask a Question
      Advertisement

      Tips

      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Name
      Please provide your name and last initial
      Thanks for submitting a tip for review!

      Warnings

      • The battery and the wire can become hot, so you may want to wear gloves if you will be handling the magnet after it has been connected for a few minutes.
      • Always be careful when dealing with electricity.
      Advertisement

      About This Article

      Thanks to all authors for creating a page that has been read 167,057 times.

      Reader Success Stories

      • Owen Martini

        Mar 14, 2019

        "I needed to make one for my schoolwork. Thanks to you, I have a passing grade!"
      Share your story

      Did this article help you?

      Advertisement