PDF download Download Article
Open your door quickly and easily with a few simple tools
PDF download Download Article

Lock drilling is the last resort if you’re locked out of a door and you need to get in fast. While drilling the lock will destroy it, you won’t have to pay (or wait for) a locksmith and the old lock can always be replaced. Plus, it's pretty simple—drill a hole just above the keyhole to destroy the tumblers, then use a flathead screwdriver to open the door. We’ll break it down for you in detail below.

Things You Should Know

  • Drill into the lock just above the keyhole. The goal is the drill through all of the pins inside the lock cylinder.
  • Go slow, and whenever the drill bit gets stuck, switch to the next size up and keep going.
  • After you drill through the pins, insert a flathead screwdriver into the keyhole and twist it to unlock the door.
Section 1 of 1:

Drilling Out a Lock

PDF download Download Article
  1. The only locks you can drill out are the doorknob locks and deadbolts with traditional tumblers. Tubular locks, ceramic locks, smart locks, cam locks, and mortise locks can only be drilled out or disassembled by locksmiths. [1]
    • Basically, if the keyhole isn’t set in a circular metal platform and the key isn’t a “normal” key, you must break the lock to open the door.
    • It's also important to double-check and make sure that you're working with a basic tumbler lock that you'll be able to knock out.
    • Trying to drill out a non-tumbler lock may destroy your door, drill bit, drill, or lock mechanism and make it even harder to get in.
    • If you’re struggling to picture what kind of lock you can drill out, just imagine any interior door in a standard home. Those kinds of knob locks and deadbolts can be drilled out.
  2. Any type of drill bit should work, but steel, black oxide, and titanium drill bits will work best. To drill through a lock, you need: [2]
    Advertisement
  3. If you don’t have the steadiest hands with a drill, punch a divot just barely above the keyhole’s shear line to guide your drill. [3]
    • The shear line is where the pins enter the lock’s opening to meet the key’s ridges, so if the lock is installed where the key’s ridges point up when you open it, put the center punch just above the top of the opening.
    • Some locks are installed upside down. If the key would go into the keyhole with the ridges pointing down, set the center punch guide hole on the bottom.
  4. If you don't have a bit that size, go with something in the neighborhood. So long as the bit is roughly as big as the widest part of the keyhole, it will work. [4]
  5. Hold the drill straight and go slow. The goal here is to destroy the pins inside the lock cylinder which allows you to force the lock open. Most locks have about five tumbler pins to drill through, although some have six or more. [5]
    • You’ll feel more resistance as the drill bit encounters each pin. That’s completely normal.
  6. Don’t try to drive through the entire lock all at once. You’re just going to break the drill bit if you force it too hard. Feel the drill work and stop once it gets stuck or starts spinning in place. [6]
    • Keep the drill level while drilling. If you drill at an angle, you can accidentally drill through unnecessary metal and your door.
  7. After going through with your smaller bit, take it up a notch. Attach a 1/4-inch (6.5mm) or larger drill bit to your drill, and go through the lock again with the larger bit to break up the pins more and open the lock. [7]
    • It normally only takes 2 drill bits to get through a traditional lock, but use a third bit that’s even bigger if your second bit gets caught.
  8. Use a little bit of force to insert the screwdriver into the key hole ( not the hole you drilled). Turn the lock in the same direction you would with a key. If the drilling worked, the lock will turn and the door will open. [8]
  9. It’s possible you didn’t drill through all of the tumblers in the lock if it won’t open. Switch to a larger 3/4 inch (19 mm) drill bit and repeat the process. Keep using larger bits and your flathead until the door opens. [9]
    • If you still can’t get the lock to open, contact a locksmith. There may be an anti-drill plate installed behind the tumblers that you can’t see keeping you from opening the door.
  10. Advertisement


Community Q&A

Search
Add New Question
  • Question
    Will this work on a tall file cabinet too?
    Glenn Letteer
    Community Answer
    File cabinets generally have two types of locks, pin tumber and waffer. It is not possible to drill a waffer lock as they have no shear line. The keyways on file cabinet pin tumbler locks are very small. As such, if you are going to attempt drilling one, you need a much smaller bit. If you choose the wrong bit size, you may split the cylinder plug. If this happens, you have a problem on your hands.
  • Question
    Can I drill a front door tumbler that has locked me in?
    Upnorth Here
    Top Answerer
    Yes, you can generally drill any lock cylinder that is not made of metal harder than your drill bit. If your front door is a required "means of egress" for fire safety, it should not require any keys to exit. In many places it would be a violation of fire code and building code.
Ask a Question
      Advertisement

      Video

      Tips

      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Name
      Please provide your name and last initial
      Thanks for submitting a tip for review!

      Warnings

      • Do not touch the drill bit or the lock with bare fingers while drilling, as it will be extremely hot.
      Advertisement

      Things You'll Need


      About This Article

      Article Summary X

      Before you attempt to drill a lock, keep in mind that you won't be able to drill locks that have a center pin made of steel or a ball bearing in the middle pin. To get started, hammer a center punch into a point just above the keyhole and take it out. Then, using an 1/8-inch drill bit, slowly drill through the point you made with the center punch. Next, replace the drill bit with a 1/4-inch bit, and repeat the process. Finally, insert a flat-head screwdriver into the lock and turn it to unlock the door. To learn how to tell what kind of lock you're working with, read on!

      Did this summary help you?
      Thanks to all authors for creating a page that has been read 569,860 times.

      Reader Success Stories

      • Omar Acevedo

        Oct 7, 2016

        "I found it very informative and helpful. Hopefully, I can follow the directions given precisely and obtain similar ..." more
      Share your story

      Did this article help you?

      Advertisement