PDF download Download Article PDF download Download Article

Learning how to drill pilot holes properly is an essential part of working with wood. A pilot hole is a small hole drilled before driving a screw into a piece of wood. The hole helps in multiple ways: it prevents the screw from splitting the wood; it allows for easier installation in dense hardwoods; and, it ensures that the screw will be installed straight, because it will follow the path of the pilot hole. Before attempting a woodworking project of any magnitude, you should learn how to make a pilot hole.

  1. If it is crucial that the screw is installed in a precise location, you may want to mark the spot with a pencil on the material. Use a ruler to determine your intended location (usually by measuring the distance from the edge of the material's surface), tracing along the ruler with a pencil. At the desired distance along the line you drew, make a small mark with the pencil.
  2. A punch is a small, slender tool with a pointed end that allows you to create a small indentation in the work surface. This indentation will help keep your drill bit from slipping when starting the pilot hole. Position the tip of the punch over your pencil mark, and then strike the punch gently with a hammer.
    Advertisement
  3. As a general rule of thumb, your pilot hole should be slightly smaller than the diameter of your screw. This will remove as much material as possible, which will reduce the likelihood of splitting, but will still leave enough material for the screw's threads to grip into.
    • Exact recommendations for pilot hole diameters based on screw sizes can be looked up online. However, a visual check of your drill bit against the screw will suffice for most applications. It is best to err on the smaller side when choosing a bit; a pilot hole can always be made bigger, but not smaller.
  4. After choosing a bit and fitting it into your drill, position the tip of the bit into the indentation you created with the center punch. Holding the bit at the angle you want the screw positioned, drill the hole to a depth equal to the screw's length. Back the bit out carefully.
  5. Once the pilot hole is drilled, you can install the screw. Fit your drill with a screwdriver bit and position the screw's tip into the pilot hole. Drive the screw in, being careful to angle it to follow the path of the hole. Repeat this process for each screw used.
  6. Advertisement

Community Q&A

Search
Add New Question
  • Question
    I don't have a drill and I'm hanging a curtain rod. How do I get the screw started?
    Community Answer
    The tip of a screwdriver should work.
  • Question
    Can I use a 5/32 bit instead of a 7/32 bit for a pilot hole?
    Community Answer
    You need the pilot hole to be smaller than the screw diameter you will use, otherwise screws will not hold.
  • Question
    How do I start a hole in my screen door to put in a new closure?
    Julie
    Community Answer
    You could use a punch or a screw driver. Just start the screw to puncture or dent the metal.
See more answers
Ask a Question
      Advertisement

      Video

      Tips

      • Pilot holes are not necessary when installing screws in very soft materials like gypsum board (drywall). These materials pose little risk of splitting or misaligning your screws.
      • Pilot holes are especially necessary when installing screws near the edge of a piece of wood or into a very thin piece of wood. These tasks present the highest risk that the wood will split when screwed into.
      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Name
      Please provide your name and last initial
      Thanks for submitting a tip for review!
      Advertisement

      Things You'll Need

      • Ruler
      • Pencil
      • Center punch
      • Hammer
      • Drill
      • Drill bits
      • Screw

      About This Article

      Thanks to all authors for creating a page that has been read 344,287 times.

      Reader Success Stories

      • Sue Evans

        Jun 6, 2016

        "Thank you; I needed to screw some letters to a board and had issues with the wood splitting, so I needed to ..." more
      Share your story

      Did this article help you?

      Advertisement