PDF download Download Article
Common problems and fixes for a Keurig Coffee Maker
PDF download Download Article

Keurig coffee makers make brewing coffee so easy and convenient. However, that doesn't mean they don't have their problems. You may start to experience problems with your Keurig machine, such as not brewing, not turning on, leaking, bad coffee taste, etc. This wikiHow article teaches you how to troubleshoot common problems with a Keurig coffee maker.

Quick Steps

  1. Reset your Keurig and check the power outlet.
  2. Descale your Keurig and run a few cycles without a K-cup.
  3. Unclog the inside of the needle with a paper clip.
  4. Turn your Keurig upside-down and shake it.
  5. Make sure the reservoir isn't damaged and is seated properly.
  6. Check for flashing lights and beeps.
1

Reset your Keurig.

PDF download Download Article
  1. If your Keurig isn't responding when you press the buttons, you may need to reset it . To do so, power it off. Then unplug it for 30 seconds. Plug it back in and power it on.
  2. Advertisement
2

Test the electrical outlet.

PDF download Download Article
  1. If your Keurig won't turn on, check to make sure it is getting power. Try plugging it into a different electrical outlet. Make sure the breaker that controls the electrical outlet your Keurig is plugged into hasn't popped.
    • Sometimes running your Keurig along with other appliances (such as a toaster oven or air fryer) that are plugged into the same outlet or wall will cause your breaker to pop. Make sure you limit the number of appliances running at the same time.
3

Run a few cycles without a K-cup.

PDF download Download Article
  1. If your Keurig is only producing a small amount of coffee or there are grounds in your coffee, it could be clogged or there is build-up inside the tubes. Fill the reservoir with water and run several brewing cycles without a K-cup until the reservoir is empty. This will help flush out your Keurig and clean the inside.
  2. Advertisement
4

Descale your Keurig.

PDF download Download Article
  1. This will help clean out any limescale build-up inside your machine. You can descale your Keurig using Keurig cleaning solution or a mix of half water and half vinegar. Pour the solution into the reservoir and run several cycles without a K-cup until the reservoir is empty. Then wash the reservoir and run a few more cycles with just water to flush out the vinegar or cleaning solution.
5

Clean the needle and K-cup holder.

PDF download Download Article
  1. If you get grounds inside your drink or it's not brewing properly, you can clean the needle, K-cup holder, and surrounding area with a small, soft bristle brush. You can also unclog the inside of the puncture needle using a special tool. If you don't have a special tool, cleaning expert Ryan Daniel Santos tells us that you can clean the inside of the needle using a paper clip or a toothpick.
  2. Advertisement
6

Turn your Keurig upside-down and shake it.

PDF download Download Article
  1. One thing you can do to fix your Keurig if it's not brewing or barely brewing is to unplug it and remove the reservoir and tray. Turn your Keurig upside down over a sink and gently shake it. Then tap on the bottle a few times and shake it some more. Plug it back in and see if it works. [1]
7

Use bottled water.

PDF download Download Article
  1. If your tap water is particularly hard, you may get a lot of build-up inside your Keurig rather quickly. Try using bottled water instead, or put a filter on your water faucet.
    • Keurig recommends against using distilled water or overly soft water.
  2. Advertisement
8

Change the water filter.

PDF download Download Article
  1. If your coffee is starting to taste stale, it's not dispensing as much coffee, or there is excessive build-up, it may be time to change the water filter . Not all Keurig models have a water filter. To replace the water filter, purchase a new cartridge and rinse it. Remove the old cartridge from the holder and insert the new cartridge. Reinsert the cartridge holder back in the reservoir. [2]
9

Make sure the reservoir isn't damaged.

PDF download Download Article
  1. If your Keurig is leaking water, check to make sure the reservoir tank isn't damaged. Check the O-ring on the nozzle on the bottom of the reservoir to make sure it isn't damaged. If it is, you can purchase a new O-ring to replace it. Make sure the reservoir is seated properly.
  2. Advertisement
10

Make sure the reservoir is seated properly.

PDF download Download Article
  1. If your Keurig is leaking or dispensing too much water, remove the reservoir and reseat it. Make sure it is seated properly against the machine. Also, check to make sure you aren't filling the reservoir past the fill line.
11

Check your Keurig for flashing lights or beeps.

PDF download Download Article
  1. If you see flashing lights or hear beeps, your Keurig could be trying to alert you to a problem. Flashing lights and beeps may mean something different for different models. Consult the user's manual or manufacturer's website to see what the beeps and flashing lights mean.
    • For example, a flashing light might indicate that you need to descale your Keurig or clean the needle.
  2. Advertisement
12

Contact Keurig customer support.

PDF download Download Article
  1. If you've tried everything and your Keurig is still malfunctioning, there could be a problem with the internal components. In this case, you will need to contact Keurig support. [3]
    • You can call Keurig support at 1-866-901-2739.

Expert Q&A

Ask a Question
      Advertisement

      Tips

      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Name
      Please provide your name and last initial
      Thanks for submitting a tip for review!

      About This Article

      Thanks to all authors for creating a page that has been read 12,657 times.

      Did this article help you?

      Advertisement