Download Article
Download Article
Seat belts are one of the most important safety features of a vehicle. However, sometimes obstructions inside the seat belt buckle can prevent the device from operating as intended. You might even need to remove one of the seats to make it easier to access the inside of the buckle! Luckily, rather than spending money to replace your whole seat belt system, it’s possible to fix the buckle yourself with just a few easy steps.
Steps
-
Inspect the seat belt tongue for deformities. These can cause the seat belt buckle to latch improperly or to release only with great difficulty. The tongue is the silver shaped part of the buckle with a hole in the center, also sometimes referred to as the “male” connector. [1] X Research source
- If the seat belt tongue is deformed, it will likely need to be replaced entirely.
-
Wiggle a thin or pointed object in the buckle. An item such as a butter knife will do nicely. This will hopefully dislodge any foreign objects that may be inside, and is usually sufficient to restore the buckle to proper working order. [2] X Research source
- Items like paper clips, coins, and even small toys can get lodged inside the buckle, impeding the releasing and latching of the tongue.
Advertisement -
Remove the female part of the buckle from the side of the seat. This might require removing the front seats to gain access to the nut and bolt holding the buckle in place. To remove the nut and bolt, use a basic socket set and ratchet or a simple wrench. [3] X Research source
-
Turn the buckle upside down and wiggle a thin or pointed object inside. Again, a butter knife would work well. If you’re certain there is an object inside the buckle, try to shake the buckle as you wiggle the pointed object to increase the chances of the obstruction falling out. [4] X Research source
-
Pry the buckle open if the foreign object remains inside the buckle. Some buckles can be opened by loosening a couple screws. Otherwise, use a flathead screwdriver to force the buckle open. Exercise caution as you open the buckle, as springs and other buckle parts might fly free when you do this.
-
Test the buckle after removing the foreign object. Push the red button and make sure the springs and other internal mechanisms are operating properly. If the springs are rusty, spray a lubricant like WD-40 on the springs to smoothen the spring action. [5] X Research source
-
Reassemble the seat belt buckle. Find the indentation on the plastic cover, as this is the side that should point towards the clip. Press the plastic cover back onto the buckle, then bolt the buckle back in place. If the buckle still won’t work, you will have to replace it entirely. [6] X Research source
Advertisement
-
Slide the seat as far forward as it can go. Most cars have front seats that are bolted to the floor at the front and rear end of the sliding rails. By moving the seat forward, you will expose those bolts so they will be easier to remove. [7] X Research source
-
Take out the seat belt anchorage point with a socket wrench. Seat belt anchorages are often hidden behind a piece of trim. Lift the seat belt portion away, then place the bolt that you just removed back in place so it doesn’t get lost. [8] X Research source
-
Remove the bolts at the back of the sliding rails and tip the seat forward. Make sure not to over-torque the bolts when you remove them. Disconnect any electric wires still connected to the seat, then maneuver the seat as needed to gain easier access to the seat belt buckle. [9] X Research source
- Make sure the ignition is off and the key is removed.
-
Reconnect the electrical wires to begin reinstalling the seat. Again, make sure the ignition is off and the key is removed from the ignition. Otherwise, you risk inadvertently electrocuting yourself or damaging your car. [10] X Research source
-
Maneuver the seat back onto the sliding frames and screw in place. There should be hooks in the front of the seat and two locator pins on the rear that will drop into place. Push the seat as far forward as possible on the rails, then screw the bolts belonging on the runners back in place. [11] X Research source
- Torque the bolts to 30 newton meters (or 20 pounds per foot). If torqued any harder, the bolts might be under too much tension to distribute force properly in the event of a crash. [12] X Research source
Advertisement
Expert Q&A
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Video
Tips
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Warnings
- Always exercise caution when tampering with the safety features of a vehicle, and consult a professional mechanic if you are uncertain of how safe your seat belt is.Thanks
- Make sure your car’s airbag system won't activate while you tinker with the seat belt. In some cars, the seat belt sensor can trigger an airbag to go off, or at least a seat belt alarm. [13] X Research sourceThanks
Advertisement
References
- ↑ https://scanneranswers.com/diy-seat-belt-repair-how-to-fix-seat-belt-buckle/#how-to-fix-seat-belt-buckle-8211-the-long-way
- ↑ https://scanneranswers.com/diy-seat-belt-repair-how-to-fix-seat-belt-buckle/#how-to-fix-seat-belt-buckle-8211-the-long-way
- ↑ https://scanneranswers.com/diy-seat-belt-repair-how-to-fix-seat-belt-buckle/#how-to-fix-seat-belt-buckle-8211-the-long-way
- ↑ https://scanneranswers.com/diy-seat-belt-repair-how-to-fix-seat-belt-buckle/#how-to-fix-seat-belt-buckle-8211-the-long-way
- ↑ https://scanneranswers.com/diy-seat-belt-repair-how-to-fix-seat-belt-buckle/#how-to-fix-seat-belt-buckle-8211-the-long-way
- ↑ https://gwrco.com/latest_news/gwr-cantilever-buckle-saves-lives/
- ↑ https://www.youtube.com/watch?v=jrLkWw2hb7Y&feature=youtu.be&t=13
- ↑ https://www.youtube.com/watch?v=jrLkWw2hb7Y&feature=youtu.be&t=50
- ↑ https://www.youtube.com/watch?v=jrLkWw2hb7Y&feature=youtu.be&t=83
About This Article
Thanks to all authors for creating a page that has been read 189,146 times.
Advertisement