PDF download Download Article PDF download Download Article

Double ring belts are a type of belt, usually made out of a more casual material like canvas, that are fastened using a set of 2 metal rings in place of a belt buckle. If you’ve never worn a double ring belt before, it’s easy to get confused when you’re trying to tighten the belt for the first time. However, once you get the technique down for threading the end of the belt through both rings correctly, it’s just as easy as fastening any other belt. Double ring belts are a great addition to any casual summer outfit or a practical everyday belt when you want a highly adjustable fit.

Fastening a Belt with Two Loops

Pull the end of the belt over the top of the first ring, then under the second ring. Keep pulling the end through until the belt is comfortably tight. Then, secure the loose end.

Part 1
Part 1 of 2:

Fastening a Double Ring Belt

PDF download Download Article
  1. Stand up straight with a pair of pants on, buttoned and zipped up. Put the end of the double ring belt through the front loop on your left side, then pull it through all the other loops until it is wrapped all the way around your waist. [1]
    • This applies to any kind of double ring belt. It doesn’t matter if the rings are D-shaped, O-shaped, or square.
    • You could put the belt through the loops in the other direction, starting with the loop on your right side, if you want. However, starting on the left is the typical way belts are worn.
  2. Pull on the end of the belt or the rings themselves to reposition the rings. Make sure they are on top of the top button at the front of your pants. [2]
    • The rings go in the same place that a standard belt buckle would go.
    Advertisement
  3. [3] Hold the rings in your left hand and use your right hand to slide the tip of the belt through the rings, going towards your left. Pull the belt all the way through. [4]
    • The belt will still be loose at this point as you have not created any tension yet.
  4. [5] Pull the end of the belt back towards your right, going over the top of the first ring. Slide the tip of the belt under the second ring and pull the end all the way through until the rings are flat against the front of your waist. Keep pulling the end of the belt until it feels comfortably tight around your waist. [6]
    • You might have to re-center the rings as you tighten the belt by sliding them to the left or right on your waist.

    Tip : You can keep the rings separated by putting a fingertip in between them to get the belt over the first ring and under the second ring more easily.

  5. Advertisement
Part 2
Part 2 of 2:

Securing the Loose End in Different Ways

PDF download Download Article
  1. Slide the tip of the loose end of the belt through the first belt loop on your right-hand side. Pull the slack all the way through so the belt rests flat on top of itself. [7]
    • Double ring belts don’t usually have their own “keeper loop,” or loop to secure the end of the belt with, as regular belts do, so you have to secure the end in a different way.

    Tip : If there is still a lot of loose belt hanging after you slide it through your first belt loop, put the tip through the next belt loop as well.

  2. Hold the end of the belt straight and flat against your waist. Slide a bobby pin over the loose end and the section of belt directly underneath it to clip it in place. [8]
    • If you don’t have a bobby pin, you could use a hair tie instead. Just slide the hair tie over the belt before you put it on, then put the loose end of the belt through the hair tie to hold it in place.
  3. Slide the tip of the loose end of the belt behind the section of belt just to the right of the rings, between the belt and the waist of your pants. [9] Pull the tip straight down so the loose end of the belt rests flat against the front of your thigh. [10]
    • This is a good way to give the belt a relaxed care-free look while still securing the loose end in place so it doesn’t flap around. For example, you could dress down a pair of khakis and a button-up shirt by wearing a double ring belt this way.
  4. Pass the tip of the loose end of the belt over the first belt loop on your right hand side, then slip the tip between the belt and the waist of your pants, from the top edge of the belt downwards. Pull the tip out from the bottom edge of the belt, then pull it straight to your right so the loose end of the belt is twisted around the section of belt on your hip. [11]
    • This is a good casual way to style a double ring belt with a little flair. You could wear a canvas double ring belt this way with a pair of khaki shorts and a striped T-shirt to get a classic summery boat wear look, for example.
  5. Put a strip of double-stick tape on the back side of the belt’s loose end. Press it firmly against the section of belt directly underneath it to stick it in place. [12]
    • This method could be a good option if your belt is either too short for the end to reach your first belt loop or if it is too long and the end still dangles after you put it through your belt loop.
  6. Advertisement

Expert Q&A

Search
Add New Question
  • Question
    How do you loop a belt that's too long?
    Sahra Brandt
    Personal Stylist
    Sahra Brandt is a Personal Stylist and the Founder of Shop the City, a company dedicated to helping others attain their style goals. With over ten years of fashion industry experience, Sahra specializes in wardrobe audits, personal shopping, and remote styling. She also runs Que Sera Sahra, a lifestyle blog. Sahra holds a BBA in Fashion Merchandising and Visual Merchandising from LIM College.
    Personal Stylist
    Expert Answer
    Try doing a knot using the tail end of the belt, the one that's drooping. Then, put that knot through the belt loop.
Ask a Question
      Advertisement

      Video

      Tips

      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Name
      Please provide your name and last initial
      Thanks for submitting a tip for review!

      Tip

      • When you want to loosen a double ring belt, just hook your fingers under both of the rings and pull them away from your waist.

      Things You’ll Need

      • Double ring belt

      About This Article

      Thanks to all authors for creating a page that has been read 431,346 times.

      Did this article help you?

      Advertisement