Download Article
Download Article
This wikiHow will teach you how to put together or fix a UK three-pin plug.
Steps
-
Strip the end of the thick cable coming from the appliance into the plug, using wire strippers. Take off roughly 3 centimeter (1.2 in) of white covering, leaving you with three thinner cables. [1] X Research source
-
Undo the Philips screw in the center of the plug, on the side with the three pins poking out.Advertisement
-
Take the back off of the plug (the part you loosened by undoing the screw).
-
Leaving the plug on a desk/table/floor, take the stripped end of the thick white wire and separate the three wires inside it from each other, so each one is relatively maneuverable.
-
Strip roughly 0.5 to 1 centimeter (0.2 to 0.4 in) off of the end of the blue, brown and striped wires, so that the copper insides are clearly visible.
-
See the diagram below, in the External Links section for a clearer view.
-
Put all three wires through the cable grip, along with the thick white cable, until the cable grip can be securely tightened onto the thick white cable. The cable grip may have to be loosened with a Philips screwdriver in order to fit the cable underneath it. [2] X Research source
-
Undo the screws on top of the holes to allow the wires to go into the holes and get a good contact with the metal.
-
The Blue (Neutral) wire (bl = bottom left) goes into the hole in the bottom left (when the three pins of the front of the plug are facing away from you). [3] X Research source
-
The Brown (Live) wire (br = bottom right) goes into the hole on the right, connected to the fuse (which should be clipped in). [4] X Research source
-
The green and yellow wire is the earth wire, and goes through the middle up to the hole in the top.
-
Put the back of the plug back on once all the wires are in and tight, and all the screws are securely done up.
Advertisement
Community Q&A
Search
-
QuestionHow would I wire a brown and blue cable?Community AnswerBlue to the left and brown to the right, as shownabove. It's a standard cable for a device which doesn't need an earth wire.
-
QuestionIf the wires are black and red, which is Live and which is Neutral?Community AnswerRed will be Live and Black will be Neutral.
-
QuestionThe cable for my hob has four wires: green/yellow, blue, black and brown, whilst the plug only takes three. Can I use either the brown or black?Community AnswerNo! Usually a brown wire is live and black or blue wires are neutral, so they are NOT interchangeable. I haven't seen such a connection in my hobs, so I would recommend that you contact the supplier, manufacturer, or a professional electrician.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Tips
- You will have to take out the fuse to put the wires in place inside the plug. Make sure you put it back in afterwards or the plug won't work as there will not be a complete circuit without the fuse.Thanks
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement
Warnings
- This can go quite wrong if wired incorrectly, and death/serious injury can occur.Thanks
- If unsure, it may be a good idea to have an electrician check things over/do the whole job himself, as getting this wrong can be very dangerous .Thanks
Advertisement
Things You'll Need
- Wire strippers
- A thin Flathead screwdriver
- A small Philips screwdriver
- Good hands
Expert Interview
Thanks for reading our article! If you’d like to learn more about electrical wiring, check out our in-depth interview with Ricardo Mitchell .
References
About This Article
Thanks to all authors for creating a page that has been read 350,404 times.
Reader Success Stories
- "Used a 3a fuse instead of a 13a had to rewire new plug, this was very helpful."
Advertisement