Download Article
Download Article
Replacing a leaking radiator hose on your car is fairly easy. All you need are a few basic tools, a basic knowledge of how your vehicle is designed, and some replacement coolant. While you can always tape the gap up to prevent more liquid from leaking out of the hose, you’re best off solving the problem permanently. You can save money on a mechanic and leave yourself with a sense of accomplishment if you learn how to replace a leaking radiator hose.
Get Car Support Solve Any Problem
Try Asking:
We’re sorry we don’t support the car you are looking for. Please enter its make, model, and year below so that we can add support for it.
Thank you! We’ll review your request and add support for this product as soon as possible. In the meantime, you can ask more questions about the products we currently support.
Steps
Download Article
-
Begin by identifying the leaking radiator hose that needs to be replaced. Do this by running the car to operating temperature. [1] X Research source
- Park the car on level ground with the engine running in park and emergency brake set.
- With the car running, visually inspect the hoses for collapse or leaks and do the same thing with the engine off.
-
Drain the engine coolant when it has cooled. Open the petcock on the lower end of the radiator and drain it into a bucket. [2] X Research sourceAdvertisement
-
Loosen the clamps on the leaking radiator hose.
-
Grab hold of the hose and begin to work it off of the end it is attached to. [3] X Research source
- Remove the hose clamps from the leaking radiator hose.
- If the hose will not slide off easily use a carpet knife to make a slice parallel to the hose from the hose end to just past the nipple it is attached to. Peel the hose from the nipple like an orange.
-
Push the hose firmly over the stub-out from the radiator and engine seating firmly over the rib that runs around the outer section of the stub-out as far as possible.
-
Slide the clamps down the hose to within the width of the clamp off the end of the hose and tighten as necessary. [4] X Research source
-
Close petcock on the bottom of radiator and begin filling of radiator with the proper mixture and type of coolant.
-
Put the radiator cap back on and continue filling the system up at the coolant reservoir to cold level.
-
Start the engine and allow it to come to operating temperature.
-
Check for leaks watching the fluid level in the reservoir tank which should drop as the thermostat opens up.
-
Drive vehicle as you would normally and check coolant levels and recheck for leaks.
-
With the radiator cap off, allow to drain into a pan at least 2 gallon/3.8 liter in size.
-
When you turn the engine off the back pressure should reveal any leaks not seen.
- Top off the coolant as needed. [5] X Research source
-
Slide the clamps onto the new hose.
Advertisement
Community Q&A
Search
-
QuestionHow do I get a hold of the clamp on the bottom of the top hose?Community AnswerIf you can see the nut, you need a very long screw driver or a socket with long extensions. If not, you need to wiggle your hand through the best you can to get at it.
-
QuestionThe hose that connects the radiator to the engine is loose and is leaking. How do I safely reattach it?Community AnswerMake sure the engine is cool and then tighten the clamps. If that doesn't help, replace the hose and clamps.
-
QuestionThey forgot to put the clamp on the coolant hose and the hose came off, what kind of damage did it cause?Community AnswerIf the car got very hot you could have gotten a blown head gasket or lost all the coolant. If the clamp is back on and the car is not overheating, you're in good shape. If it is overheating, bring it back to the person who forgot the clamp and have them fix it.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Video
Tips
- Clean off the stubs from the engine and radiator to remove any old pieces of hose still stuck on them before installing a new radiator hoseThanks
- The two types of clamps are pinch type and screw type. With the pinch type, use a pair of pliers to pinch the two ears on the clamps and slide them back off of the end of the hose. On a screw type, use a flathead screwdriver to loosen the ratchet mechanism that tightens or loosens the band on the clamps.Thanks
- There will be a top hose running from the radiator to the engine thermostat housing (usually located at the top section of the engine above the water pump). On a rear-wheel-drive car, it will be at the front of the engine. On a front-wheel-drive car, you will find it on the right (or passenger side) of the car. The second radiator hose is located at the bottom of the engine coming off of the water pump running to the bottom of the radiator.Thanks
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement
Warnings
- Allow the engine to cool before draining coolant to avoid scalding.Thanks
- Do not drain coolant onto the ground, as this is hazardous waste and needs to be disposed of properly. [6] X Research sourceThanks
Advertisement
Things You'll Need
- Flathead screwdriver
- Medium-to-large pliers
- SAE/Metric combo wrench set
- Ratchet socket set
- 2 gallon (7.6 liter) pan
- Box cutter
- Paper towels
- Petroleum jelly
- Funnel
- 1-2 gallons (3.8-7.6) liters of 50/50 coolant
- Specific radiator hose for your car
Expert Interview
Thanks for reading our article! If you’d like to learn more about car maintenance, check out our in-depth interview with Duston Maynes .
References
- ↑ https://www.2carpros.com/articles/car-is-leaking-coolant
- ↑ https://www.popularmechanics.com/cars/how-to/a78/1272246/
- ↑ https://www.dummies.com/home-garden/car-repair/heating-cooling-system/how-to-replace-a-radiator-or-heater-hose/
- ↑ https://www.2carpros.com/articles/replace-radiator-hoses
- ↑ https://www.autoblog.com/2016/11/09/how-to-top-off-car-coolant/
- ↑ https://www.bobvila.com/articles/how-to-dispose-of-antifreeze/
About This Article
Thanks to all authors for creating a page that has been read 173,122 times.
Reader Success Stories
- "Came to work and could hear hissing from my engine hoses. This article let me know what it might be and how to properly fix the issue." ..." more
Advertisement
"Came to work and could hear hissing from my engine hoses. This article let me know what it might be and how to properly fix the issue."
..."
more
"wikiHow is a very good teacher. Any information you can get very easily, and it is surely very helpful."
"It showed me how to check my coolant system."
"Just reading this article helps a lot."
"Very helpful tips. Thanks."
