Download Article
Download Article
One of the most versatile electric tools available to a woodworker is the router. The router comes in 2 forms, the fixed base and the plunge base. The router used most by the woodworker is the plunge base. It may seem more difficult to use at first, but you can learn how to use a plunge router by following the steps below.
Steps
Download Article
-
Examine the plunge router. You will note that it contains an electric motor mounted between two posts. The motor rests on top of springs and is attached to a flat base that guides the motor down at a 90 degree angle. [1] X Research source
- The motor rises back into position when downward pressure is released, raising the router bit above the base.
- Attached to a collet, the motor connects much like a hand drill chuck. It comes in 2 sizes, 1/4 inch and 1/2 inch (as well as 8 mm and 12 mm in metric sizes). This is where the router bit does the cutting.
-
Notice the plunge router motors come in a variety of sizes ranging from 1.5 horsepower to 3.5 horsepower. The bigger the motor, and consequently the collet, the bigger the router bit. As a result, the cut is deeper. [2] X Research sourceAdvertisement
-
Research and buy what you can afford. Remember, a higher price does not necessarily mean a better tool. [3] X Research source
-
Use jigs and guides with the plunge router. These are often shop made or bought as add-on accessories.
- The most common jig will be used for cutting dadoes. Dadoes are used in joining two pieces of wood at 90 degrees, such as adding a kitchen cabinet shelf to a side piece. This type of joint uses a straight cut router bit for dadoes.
- Clamp the guide into place so that, when the router bit is plunged downward, the bit will line up with the dado joint you want to cut.
-
Install the router bit in the collet, adjusting the gauge for the depth of cut you need. [4] X Research source
-
Put the router up against the guide. Pull the trigger and push downward while holding the router with both hands. This act will engage the bit with the wood.
-
Move the router from left to right in the direction of the cut.
-
Release the downward pressure on the handles when you finish the cut. The router will retract into the base.
-
Use other bits to cut profile edges with a plunge router following the same procedure.
- Install the desired router bit in the collet. Most profile-edge bits, like a round over or Roman Ogee bit, will have a sleeve bearing that will guide the bit along the edge of the work piece.
- Set the depth gauge for the amount of bit you want to use.
-
Set the plunge router base onto the surface. Firmly press downward, holding the handles while pulling the trigger. [5] X Research source
- Push in against the edge engaging the bit while fully extended to the depth needed.
-
Make the cut with the router moving from left to right.
-
Release the downward pressure on handles and the bit will retract.
Advertisement
Community Q&A
Search
-
QuestionHow do I build a router table?DonaganTop AnswererTake a look here: TheBalance.com/free-router-table-plans-1357138.
-
QuestionHow do I use an angle grinder as a wood saw?DonaganTop AnswererThere's an old saying: use the right tool for the job. There are so many kinds of saws available, it's hard to imagine that you couldn't find a size and tooth pattern to fit the job at hand. A grinder will burn your wood and generally exasperate you unless there's very little wood to remove. In that case you might consider a file, a sander, or a chisel.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Video
Tips
- A plunge router, like a fixed base router, can be used in a router table. However, it can be more difficult to adjust the height.Thanks
- Read the instruction manual thoroughly, with the router in hand. Go over the pieces and any accessories that came with it before trying to put it to use.Thanks
- Make multiple passes on deep cuts. Attempting to make one deep pass on a dadoes or rabbit joint will bog down the router. Other problems of uneven cuts and kick back will occur as well.Thanks
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement
Warnings
- Wear safety glasses and a dust mask when working with the plunge router.Thanks
- Do not wear loose clothing while operating a router.Thanks
Advertisement
Things You'll Need
- Plunge router
- Router bits
- Guides or jigs with clamps
- Dust mask
- Safety glasses
References
- ↑ https://www.youtube.com/watch?v=8Vl8Jbw3cSk
- ↑ https://www.youtube.com/watch?v=8Vl8Jbw3cSk
- ↑ https://www.wwgoa.com/article/router-basics-how-to-use-a-router/
- ↑ https://www.wwgoa.com/article/router-basics-how-to-use-a-router/
- ↑ https://www.youtube.com/watch?v=eOKco1aOygY
- http://www.popularmechanics.com/home/reviews/4301758?click=main_sr
- https://www.youtube.com/watch?v=rJGXqtOsB6A
- https://www.woodmagazine.com/woodworking-tips/techniques/routing/plunge-router?mode=step_by_step
About This Article
Thanks to all authors for creating a page that has been read 130,294 times.
Advertisement
86%
of readers found this article helpful
.
Click a star to add your vote
% of people told us that this article helped them.
