Download Article
Download Article
If you're struggling to accelerate, especially on the highway, or you notice other signs your car might not be getting enough gas, the problem can be caused by a partially blocked or clogged fuel line, fuel filter, pump, or injector. If your car won't start at all, there are a few quick tests you can run to figure out whether or not it's causing your problems.
Steps
Get Car Support Solve Any Problem
Try Asking:
We’re sorry we don’t support the car you are looking for. Please enter its make, model, and year below so that we can add support for it.
Thank you! We’ll review your request and add support for this product as soon as possible. In the meantime, you can ask more questions about the products we currently support.
-
Check the fuel pump fuse. Often, it's not the pump itself that fails to function, but the power that supplies it. Check in your owner's manual for the location of the fuse box, then find the fuse that corresponds to the fuel pump. Pull it out and inspect it for signs of failure. If the fuse is blown, it will be broken or burned. If it looks good, check the rest of the fuses related to the fuel system for signs of being blown and replace them, if necessary. If no fuses are blown, have a helper turn the key while you listen for fuel pump relay clicking on.- If you need to replace a fuse, make sure you use one with a proper amp rating, never installing one with more amps than necessary. [1] X Research source
- If you find a blown fuse, that might be a sign that you've got a high amp draw and you need to check the individual circuits. [2] X Trustworthy Source PubMed Central Journal archive from the U.S. National Institutes of Health Go to source Try to replace the blown fuel fuse and try and start vehicle. If the fuse blows again, a direct short is present and will need to be diagnosed. Take your car into the shop to get it checked out.
-
Check the voltage at the pump itself. Just because you're getting juice from the circuit doesn't mean that it's getting to the pump itself, which makes it important to check the voltage there as well. Check out your vehicle's service manual to find out where to check and the proper procedure for checking it.- Test for source voltage , to determine whether or not the good charge that's leaving the fuse is getting to the pump. If no power is making it to the fuel pump, then check the fuel pump relay circuit. You could have a bad relay.
Advertisement -
Perform a drop test using a voltmeter . Check to make sure that the power wire shows the full voltage and the grounding wire shows that it's grounded properly. If this electrical test reveals nothing, it's likely that your fuel pump is the problem and it will need to be replaced, though you can check more thoroughly by completing an additional pressure test.- If you show more than one volt difference, that means you've got a problem with corroded wires, or that you've got issues with the circuit on either the positive or negative side. [3] X Research source Take it into the shop for further testing and advice.
Advertisement
-
Eliminate the filter as a possibility. If the filter gets clogged with sediment, you can have trouble accelerating and might suspect your fuel pump has got a problem. To check it, remove the filter from the vehicle and drain excessive fuel from the filter. Use a short piece of rubber hose on the filter inlet. Blow through the filter inlet, paying attention to the resistance, which should be minimal. Inspect the screen for debris and replace the filter if necessary by blowing through the outlet side of filter into a white rag or towel. [4] X Research source -
Get a fuel pressure gauge. Commonly available at most auto parts stores for $20-30, a pressure gauge is a good investment, useful on most makes and models of cars. If you don’t want to buy one, you can also often borrow one from machine shops or auto shops who have them to lend. The test only takes a few minutes. [5] X Research source -
Hook the pressure gauge to the fuel pump test fitting. Locate your fuel pump test point, which is usually near the fuel injectors, and locate the point at which the pump hooks up with the filter injector rail. There should be a separation joint or a test port, where the pressure gauge attaches.- Different gauges may have slightly different instructions, and the location of the fuel pump varies from vehicle to vehicle, so consult your owner’s manual for more specific instructions.
-
Have a helper rev the engine while you check the gauge. Let the engine warm up slightly, then check the pressure both at idle speed and at the rated speed listed in your pump specifications. If you don’t know the rated speed, just rev the engine and see how the pressure reacts. If you have a serious problem, the needle won’t go anywhere or goes down below specifications, meaning the fuel pump needs to be replaced.- The pressure should match the specifications listed in the repair manual, and should increase as you rev the engine. If it doesn’t, you need to replace your fuel pump and filter.
Advertisement
Expert Q&A
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Video
Tips
- If your fuel pump does needs replacing, a rebuilt one is often as good as a new one, and a lot less expensive. If you’re feeling adventurous, some manufacturers supply rebuild kits. You can take your pump apart with a screwdriver and rebuilt it yourself, following directions on the kit. If that idea doesn’t enchant you, ask your service facility to locate and install a rebuilt fuel pump. It should be guaranteed at least three months.Thanks
- Proper precautions should be taken for safe testing and diagnosis. Keep a fire extinguisher nearby while working on or testing the fuel system.Thanks
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement
References
About This Article
Article Summary
X
Before you check your fuel pump, find the fuse that corresponds to the pump and pull it out to see if it is broken or burned. If it looks fine, check the voltage at the pump itself to make sure the charge that’s leaving the fuse gets to the pump. If this looks alright, then perform a fuel pressure test. Get a fuel pressure gauge, hook it up to the fuel pump test point, and have a helper rev the engine. If the needle doesn’t move or doesn’t move much, you found the problem. For more tips, including how to check the filter, keep reading our Master Mechanic reviewer’s advice!
Did this summary help you?
Thanks to all authors for creating a page that has been read 663,954 times.
Reader Success Stories
- "Just knowing what needs to be checked so when I take it to my mechanic and tell him what is wrong I know what he will telling me! Thank you so much." ..." more
Advertisement
"Just knowing what needs to be checked so when I take it to my mechanic and tell him what is wrong I know what he will telling me! Thank you so much."
..."
more
"This was the best presentation I have found, after hours of searching my car's ignition problem. It was well illustrated and easy to understand."
..."
more
"My Chevrolet Impala turns over but won't crank. When I turn it my fuel pump makes a tea kettle noise."
"This helped me rule out my fuel pump as a problem with my car running rich and failing smog. "
"This method of an electrical test worked awesome, thank you so much."
